Industry Directory | Consultant / Service Provider
Kingzom is a global leader in providing precision die-cut component parts for customers in the consumer electronics, automotive, LED,energy and medical industries.
Industry Directory | Consultant / Service Provider / Manufacturer
CHIP ON BOARD ( COB ) Manufacturer
The CF-9 Radial Lead Former forms and cuts 2- and 3-leaded taped radial components such as TO-92s, capacitors, transistors, LEDs, etc. - precisely and repeatedly, in standard and special forms. This machine is capable of forming and cutting up to 25
Form & Cut 2-, 3-, 4-, 5-, and 7-leaded Radial Components Capable of forming loose radial components at rates up to 5,000 parts per hour with a variable speed motor. Feed components by hand or with tubes (TO-220s) Reduce setup time with quick ch
Electronics Forum | Tue May 28 18:31:08 EDT 2019 | jlawson
Solder paste flux is main contributor, Lead termination chemical-oxide by products and PCB Plating-Chemicals. Reflow profile would have very limited if not no impact really unless is way off. Paste volume control and Stencil design plays a big part
Electronics Forum | Mon Jan 04 16:55:47 EST 2010 | dyoungquist
We use a HEPCO model 3000-2 (hepcoblue.com) to shorten leads on various through hole components before we solder them on a pcb. You will have to verify they have a die that works with your particular LED module. If they do, this is what I would rec
Used SMT Equipment | Chipshooters / Chip Mounters
NXT-H and NXT-Hw support placing small LEDs and bare dies at high-speed as well as performing hybrid production including flip chips.Fuji Ultra Accurate Placement Platform.Hybrid placement of wafers and SMDs. Wafer and reel part placement in a single
Used SMT Equipment | Chipshooters / Chip Mounters
NXT-H and NXT-Hw support placing small LEDs and bare dies at high-speed as well as performing hybrid production including flip chips.Fuji Ultra Accurate Placement Platform.Hybrid placement of wafers and SMDs. Wafer and reel part placement in a single
Industry News | 2011-09-12 12:04:25.0
GPD Global will showcase its Positive Cavity Displacement (PCD) 'H' Series high-resolution pumps in Booth #439 at the upcoming IMAPS 44th International Symposium on Microelectronics
Industry News | 2011-11-20 13:36:13.0
GPD Global has been awarded two Global Technology Awards in the categories of Adhesives/Coatings/Encapsulants and Dispensing Equipment for its PCD Dispensing on the MAX Series Platform
Parts & Supplies | SMD Placement Machines
0102004 ROLLER 0104008 Bracket 0104009 shaft 0104018 block 0105001 shaft 0101111 PIN 0102102 PIN 0103012 SPRING 0105003 plate 0105004 spring 0105005 plate 0105008 Tube Canvil 0109035 STOPPER 0109036 STOPPER 0101020 WASHER 0101008 PIN 00420056 PIN 010
Technical Library | 2023-08-16 18:13:53.0
In one of our Consumer Electronics projects, a smart lighting company wished to dispense silicone-based LED encapsulation material for two different product sizes. The larger product had a 9mm circular dam which required silicone dispensing flush with the top of the dam. The smaller product had a 1mm LED die that required only the top to be encapsulated. The material consisted of two parts which were mixed by weight in a 1:1 ratio. A phosphor powder was added totaling 10% of the overall weight. The phosphor required agitation to remain suspended.
Technical Library | 2016-11-17 14:37:41.0
With increasing LED development and production, thermal issues are becoming more and more important for LED devices, particularly true for high power LED and also for other high power devices. In order to dissipate the heat from the device efficiently, Au80Sn20 alloy is being used in the industry now. However there are a few drawbacks for Au80Sn20 process: (1) higher soldering temperature, usually higher than 320°C; (2) low process yield; (3) too expensive. In order to overcome the shortcomings of Au80Sn20 process, YINCAE Advanced Materials, LLC has invented a new solderable adhesive – TM 230. Solderable adhesives are epoxy based silver adhesives. During the die attach reflow process, the solder material on silver can solder silver together, and die with pad together. After soldering, epoxy can encapsulate the soldered interface, so that the thermal conductivity can be as high as 58 W/mk. In comparison to Au80Sn20 reflow process, the solderable adhesive has the following advantages: (1) low process temperature – reflow peak temperature of 230°C; (2) high process yield – mass reflow process instead of thermal compression bonding process; (3) low cost ownership. In this paper we are going to present the die attach process of solderable adhesive and the reliability test. After 1000 h lighting of LED, it has been found that there is almost no decay in the light intensity by using solderable adhesive – TM 230.
The CF-9 Radial Lead Former forms and cuts 2- and 3-leaded taped radial components such as TO-92s, capacitors, transistors, LEDs, etc. - precisely and repeatedly, in standard and special forms. This machine is capable of forming and cutting up to 25
PCB Assembly Equipment, PCB Machine, SMD/SMT Assembly, SMT assembly line, SMT plaeement line, automatic production line Semi-automatic SMT production lines ETA Electronic equipment Co., Ltd. To provide professional SMT automatic production line sol
Events Calendar | Mon Nov 25 00:00:00 EST 2019 - Mon Nov 25 00:00:00 EST 2019 | ,
Webinar: Overcoming Challenging X-Ray Problems
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
Career Center | South Plainfield, New Jersey USA | Sales/Marketing,Technical Support
Alpha, a business unit of Alent plc and the global leader in the development, manufacturing and sales of innovative specialty materials used in a wide range of industry segments, including electronics assembly, power electronics, die attach, LED ligh
Career Center | Suwanee, Georgia USA | Research and Development
Alpha Advanced Materials, a business unit of Alent plc and the global leader in the development, manufacturing and sales of innovative specialty materials used in a wide range of industry segments, including electronics assembly, power electronics, d
Career Center | Phoenix, Arizona | Engineering,Management,Production,Quality Control,Research and Development,Sales/Marketing,Technical Support
• Highly motivated, solution oriented professional with proven record synergizing scientific, engineering, and business administration backgrounds to drive and sustain customer satisfaction and long term improvements. • Articulate communicator that a
Career Center | Cavite, Philippines | Engineering,Technical Support
I had 15 years Handling SMT Equipment.
Surface Mount Technology Association (SMTA) | https://www.smta.org/LED/tech.cfm
., CALCE, University of Maryland 12:00 PM Lunch Session 3: LED Packaging 1:00 PM Solder Alloy Selection for LED Die Bonding and Package Assembly Nicholas Herrick, Alpha Assembly Solutions 1
GPD Global | https://www.gpd-global.com/co_website/pcdpumpseries-underfill-small.php
Underfill Fluid Dispense on 6 mm Die Home Products Fluid Dispense Systems High Precision Dispenser - MAX Series Large Format Board Processing - DS Series Table Top Manufacturing Loader
