Industry Directory | Consultant / Service Provider / Equipment Dealer / Broker / Auctions / Manufacturer's Representative / Training Provider
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Industry Directory | Manufacturer
Reains Underfilm is a patented Technology which pre-formed thermoplastic, It corner or edge bonds BGA/LGA/CSP packages to the PCB to improve solder joint reliability. It tape & reel packed and fully automatic pick & place on PCB.
New Equipment | Rework & Repair Equipment
Custom made reballing fixtures designed for your specific component. Allows for high yield reballing of multiple parts at one time. Use for ball attach to BGA components and for solder bumping of LGA's and QFN's. Simply send us the data sheet and
New Equipment | Rework & Repair Equipment
NEW! Nitrogen Capable for High Yield Lead Free BGA Rework. NEW! Movable top and bottom gas heaters allows for easy rework near the edge and hard to ger area's of large PCB's. For high volume BGA Rework on even the largest computer and networking b
Electronics Forum | Thu Sep 02 07:50:27 EDT 2010 | sachu_70
Just to add to my comments,solder joint voids do occur in LGA. Voids in LGA can be larger due to geometry and greater ratio of flux to solder. IPC-A-610D specifies a greater than 25% voided area is a defect for BGA, however, it does not specify the d
Electronics Forum | Mon Aug 10 12:28:17 EDT 2009 | davef
We don't know dip about your Linear Tech LGA118, but we agree with published reports that say you should have between 4800 and 7000 thou^3 of paste on the pad for a LGA. These volumes were analyzed based on volumes found successful for CGA and then e
Industry News | 2016-04-06 12:45:01.0
The SMTA is excited to announce three new workshops for the 10th Annual International Conference on Soldering and Reliability (ICSR) being held May 9-11, 2016 in Toronto, Canada. The event is co-located with the SMTA Toronto Expo.
Industry News | 2016-04-07 09:04:01.0
The SMTA is excited to announce three new workshops for the 10th Annual International Conference on Soldering and Reliability (ICSR) being held May 9-11, 2016 in Toronto, Canada. The event is co-located with the SMTA Toronto Expo.
Parts & Supplies | Repair/Rework
Three independent heaters control systems. FG-P6000 is available heating portion of the PCB board by hot-air circulate both from top and bottom at the same time. With large IR bottom heating, it can completely avoid PCB deformation during reworking
Technical Library | 2016-01-12 11:01:25.0
More and more Land Grid Array (LGA) components are being used in electronic devices such as smartphones, tablets and computers. In order to enhance LGA mechanical strength and reliability, capillary flow underfill is used to improve reliability. However, due to the small gap, it is difficult for capillary underfill to flow into the LGA at SMT level. Due to cost considerations, there are usually no pre-heating underfill or cleaning flux residue processes at the SMT assembly line. YINCAE solder joint encapsulant SMT256 has been successfully used with solder paste for LGA assembly. Solder joint encapsulant is used in in-line LGA soldering process with enhanced reliability. It eliminates the underfilling process and provides excellent reworkability. The shear st rength of solder joint is stronger than that of underfilled components. The thermal cycling performance using solder joint encapsulant is much better than that using underfill. Bottom IC of POP has been studied for further understanding of LGA assembly process parameters. All details such as assembly process, drop test and thermal cycling test will be discussed in this paper.
Technical Library | 2023-10-09 15:18:50.0
This technical document provides necessary information and general guidelines for soldering and PCB design for the Würth Elektronik eiSos MEMS sensor products with an LGA surface-mount package
The biggest, baddest, most affordable Nitrogen Capable BGA Rework Station demonstrated by Dennis O'Donnell the BGA Expert! Safe, precision rework for SMD, BGA, and LED chips on boards as large as 36" or more!. The versatile E6250U rework station co
One unit currently in stock for immediate shipment. Ships from California. The Chip Off Model 620 SMD Rework System features touch screen operation and programming, upper and lower spot hot air heaters, ceramic coated area heaters, HD Split-Vision
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Events Calendar | Mon Dec 02 00:00:00 EST 2019 - Mon Dec 02 00:00:00 EST 2019 | ,
Webinar: QFN/LGA Design, Assembly Process Issues & Reliability Failures
Events Calendar | Wed Oct 23 00:00:00 EDT 2019 - Thu Oct 24 00:00:00 EDT 2019 | Guadalajara, Mexico
SMTA Mexico Expo 2019
Career Center | Wesley Chapel, Florida USA | Engineering,Management,Quality Control
15 years of experience on Electronic Manufacturing. Certified SMT Process Engineer TQM Knowledge Statistics DOE Screen Printer Thermal Process Knowledge JIT International Project Engineering Experience
Career Center | banaglore, karnataka India | Maintenance,Production,Quality Control,Technical Support
tel u later
| https://ipcapexexpo.org/education/call-for-technical-paper-form
Extreme Requirements PCB Fabrication and Materials Quality, Reliability, Test and Inspection Other Assembly Processes Topics BTC/QFN/LGA Assembly Challenges Cleaning Coating Processes Electronics
