Industry Directory | Manufacturer
Pro Tech. Monitoring is the world leader in GPS offender Tracking.
High Precision Dispensers - MAX Series (Non-Heated) Max Series is capable of a wide variety of dispense applications including MicroVolume, Solder Paste and Conductive Adhesive, Underfill, Surface Mount Adhesive, Dam and Fill, Encapsulations, LED En
Simplify Dispensing with GPD Global’s Island Series Dispense Platforms Island Series robots give you versatility to do simple, repetitive automation jobs. Work areas range from 300 mm x 400 mm to 400 mm x 400 mm. All Island Series robots are compati
Electronics Forum | Wed Jan 10 14:15:48 EST 2001 | Claude_Couture
We have an old Conceptronic oven (Discovery Mark IV) which we use in the glue process. The video monitor just died. This is a 11 year old oven with a Goldstar model 1420 PLUS monitor. There are no specs in the manual and Conceptronic is not much help
Electronics Forum | Mon Jan 07 15:51:53 EST 2002 | radney
Does anyone know of an alternate source or a monitor that can be used in place of the old Mitsubishi monitors. Surely there is a newer replacement. Universal/Sanyo wants about $8k for these. The monitor that is in there now is a Mitsubishi XC-1498
Used SMT Equipment | Soldering - Wave
400V 50/60 HZ Version ERSAsoft for: 4.050.000.000 2. Operating System Dell / Windows 7 Processor: Pentium(R) Dual Core E5800 @ 3.20GHz 3.19GHz Memory RAM: 4.00 GB (3.46 GB usable) 320bit Operating System Touch Screen – No Pen Touch, input is availabl
Used SMT Equipment | SMD Placement Machines
* DOS * Flying Nozzle change * Fiducial camera * Pneumatic tape feeder * Locate Pin * Edge clamp * Z servo push plate * Entrance sub stop * Exit sub stop * Auto width adjust * Feeder float detection
Industry News | 2013-08-15 20:58:22.0
Heller Industries announced today that they have entered into a joint development agreement with International Business Machines Corporation (NYSE: IBM), to collaborate on the development of fluxless mass reflow furnace equipment and process for high volume manufacturing. The fluxless process utilizes gas phase formic acid to replace standard fluxing agents, and eliminates the need for pre-reflow fluxing and post-reflow flux cleanup steps.
Industry News | 2017-09-16 02:29:39.0
Heller Industries has been awarded the 2017 Global Frost & Sullivan Company of the Year Award for its surface mount technology (SMT) soldering equipment that enables Industry 4.0. - the automation and data exchange in manufacturing technologies.
Parts & Supplies | Pick and Place/Feeders
GIC-K01 KME CM402 Feeder Calibration JIG Specification: Overall size 500 x 350 x 550 mm , L x W x H Type Electric Monitor : 12” LED display, with cross mark Camera : CCD, 50 times magnification Object of Feeder CM402 / CM602 Pls kindly c
Parts & Supplies | Pick and Place/Feeders
GIC-K02 KME CM88 Feeder Calibration JIG Specification: Overall size 500 x 350 x 550 mm , L x W x H Type Pneumatic / Manual Monitor : 12” LED display, with cross mark Camera : CCD, 50 times magnification Object of Feeder CM88 Pls kindly c
Technical Library | 2018-04-27 13:23:31.0
When performing BGA component rework, it is important to know the actual heat that is coming out of the top and bottom heaters. This will be critical in setting up accurate heat profiles. Monitoring your heat output will also keep you aware of your heaters performance so that you will know when the heaters need to be replaced.
Technical Library | 2020-12-07 15:26:06.0
Temperature cycling testing is a method of accelerated life testing done to PCCs that are exposed to normal operation temperature variations over its lifetime. During the testing, intermittent "open" failures can first occur at the hot and cold extremes of the test, exposing weaknesses in the design and assembly. A poor/weak solder joint fatigues, a via trace or barrel cracks, loose connections or a component fails all causing an intermittent open. When not at extreme temperatures, the PCC assembly relaxes, the "open" closes creating electrical connectivity. If you are monitoring the PCC under test in-situ you will know that an intermittent failure has occurred, and the test could be stopped for inspection. If in-situ monitoring was not implemented, you would not know if there were intermittent failures or not. The PCC gets powered up and works fine at room temperature.
1809 MK5 - Heller Advanced In-Line Vacuum Reflow Oven Nitrogen System with Balanced Flow Technology 9 Top And Bottom Heated Zones - highest zone count per linear foot in the industry! 100" Heated Length - for super throughput! 2 Internal C
Nano-copper sintering in formic acid vapor.
Training Courses | ONLINE | | ESD Control Training Courses
Browse training and certification programs for electrostatic discharge (ESD) control in electronics assembly.
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Events Calendar | Mon Aug 10 00:00:00 EDT 2020 - Mon Aug 10 00:00:00 EDT 2020 | ,
Monitoring & Bench marking Your Processes and Assembly Yields
Events Calendar | Tue Apr 21 00:00:00 EDT 2020 - Thu Apr 23 00:00:00 EDT 2020 | Amsterdam, Netherlands
Electronics in Harsh Environments Conference
Career Center | Houston, Texas USA | Engineering,Management
Position Summary: SMT Process Engineer is responsible for all phases of Printed Circuit Board Assembly. This position oversees process development, improvement, and measurements for PCB manufacturing. Essential Job Functions (listing most importa
Career Center | MANCHESTER, United Kingdom | Engineering
Typical work activities usually include: * installing, supporting and maintaining new server hardware and software infrastructure; * managing email, anti-spam and virus protection; * setting up user accounts, permissions and passwords;
Career Center | Laguna, Calabarzon Philippines | Engineering,Maintenance,Production,Technical Support
Base on my experience more on line sustaining and preventive maintenance in equipment and testing machine for electronics and semicon company Some slight skills in surface grinding,soldering and LAN connection and installation. Can submit report
Career Center | Riyadh 11623, Philippines | Engineering,Maintenance,Production
PROFESSIONAL EXPERIENCE: Connected in the field of manufacturing/electronics industry experienced in the line, Through Hole and Surface Mount Technology, worked on various Fuji Machines Universal model, such as: CP 643E chip shooter QP 242E chip mou