Industry Directory | Consultant / Service Provider / Distributor / Equipment Dealer / Broker / Auctions / Manufacturer / Manufacturer's Representative
DONGGUAN KINGSUN AUTOMATION TECHNOLOGY CO.,LTD is a company which mainly provide used and new SMT parts, provide repair SMT key parts service,new/used SMT machine trading,SMT consumables and Peripherals equipment,Clean room, ESD..
Industry Directory | Manufacturer
DONGGUAN KINGSUN AUTOMATION TECHNOLOGY CO.,LTD is a company which mainly provide used and new SMT parts, provide repair SMT key parts service,new/used SMT machine trading,SMT consumables and Peripherals equipment,Clean room, ESD..
New Equipment | Board Handling - Conveyors
Model No: KSUN B350 Automatic vacuum loader MAX PCB`s capacity: 300pcs (0.6mm thickness PCB) cycling time: Approx 6 seconds Power supply: 100-230V AC (customized), single phase Power load: MAX 180 VA Air pressure: 4-6 bar Air volume: MAX 30L
New Equipment | Board Handling - Conveyors
Model No: KSUN 460 Automatic vacuum loader MAX PCB`s capacity: 300pcs (0.6mm thickness PCB) cycling time: Approx 6 seconds Power supply: 100-230V AC (customized), single phase Power load: MAX 180 VA Air pressure: 4-6 bar Air volume: MAX 30L/
Electronics Forum | Thu May 01 07:33:19 EDT 2008 | realchunks
Jim, You need to repair or by-pass the cover interlock. The machine thinks it's open and will not procede any further. They all do it, even the new models. Once you get past this warning - you will get the the RESET window - garanteed.
Electronics Forum | Wed Sep 27 17:49:41 EDT 2006 | SWAG
Open the rear door that has the cooling fans on it. Look at the wiper blade regulator, look toward the front of the machine about 8" or so and to then left 3"or 4". There should be a lexan cover/box over the board that has this pot. on it. If stil
Used SMT Equipment | Screen Printers
Substrate processing: Maximum substrate size (XxY): 609.6mmx508mm(24”x20”) For circuit boards larger than 20”, special fixtures are required Minimum substrate size (XxY): 50.8mmx50.8mm(2”x2”)
Used SMT Equipment | Pick and Place/Feeders
Concept: Over drive motion Ultimate access Super wide range DDH V5 Smart operation Voluntary line operation Wide open &Easy access Quick exchange Auto changeover PP type LISA Feeder hot swap Chip theory speed 84500chip Placement ra
Industry News | 2003-05-28 08:28:54.0
For June 2-4 (Mon. - Wed.)Design Automation Conference 2003
Industry News | 2009-09-26 15:37:45.0
Barry O’Brien died on Sunday, September 20, 2009 while bike riding. Barry covered the Ohio territory for Horizon Sales, a manufacturer’s representative corporation supplying machinery and supplies to the electronics industry.
Parts & Supplies | SMT Equipment
000-A E1332725010 COVER RUR PRINTED JUKI LOGO KE E1332725020 COVER RUR PRINTED JUKI LOGO KE E1333721000 COVER RUL E133372100A COVER RUL (ST) E133372100B COVER RUL (ZN) E1333725000 COVER RUL E1334721000 COVER CUR E133472100A COVER CUR (ST) E133472100B
Parts & Supplies | Pick and Place/Feeders
000-A www.fujintai.com JUKI E1332725010 COVER RUR PRINTED JUKI LOGO KE FUJINTAI TECHNOLOGY CO.,LTD JUKI E1332725020 COVER RUR PRINTED JUKI LOGO KE www.fujintai.com JUKI E1333706A00 COVER TAPE HOLD BRACKET FUJINTAI TECHNOLOGY CO.,LTD JUKI E1333721
Technical Library | 2019-05-29 01:47:22.0
1.Vias near SMD pads: Solder can flow into the via after melted. As a result cold joint will appear in the end. Check the picture below. 2.Vias on SMD pads: Solder can flow into the via more easier after melted. Check the picture below. 3.Via opening without soldermask covered. When workers solder TH parts by hand, soldering iron can touch vias sometime, then tiny amounts molten solder will stay on vias. This can lead to electrical short easily. We recommend you make all vias tenting (covered by solder mask) if it is possible.
PCBNPI-Professional PCB Fab/PCB Assembly Service Provider From China
Technical Library | 2017-08-17 12:28:30.0
At SMT assembly, flux outgassing/drying is difficult for devices with poor venting channel, and resulted in insufficiently dried/burnt-off flux residue for no-clean process. Examples including: Large low stand-off components such as QFN, LGA Components covered under electromagnetic shield which has either no or few venting holes Components assembled within cavity of board Any other devices with small open space around solder joints
Training Courses | | | IPC-6012 Specialist (CIS)
The Certified IPC-6012 Specialist (CIS) training covers design, fabrication and inspection of rigid printed boards.
Training Courses | | | IPC/WHMA-A-620 Specialist (CIS)
The Certified IPC/WHMA-A-620 Specialist (CIS) training focuses on cable and wire harness fabrication and installation.
Events Calendar | Tue Dec 08 00:00:00 EST 2020 - Tue Dec 08 00:00:00 EST 2020 | Online,
SMTA California Technology Day
Events Calendar | Wed May 31 00:00:00 EDT 2023 - Wed May 31 00:00:00 EDT 2023 | Holtsville, New York USA
Long Island Chapter Meeting: Fine Feature Paste Printing, Stencil Design and Solder Technology
Career Center | San Jose, California USA | Management
DCSI is one of the most trusted and respected global executive search and solutions companies inthe electronics manufacturing industries. We have more than 35 active openings that range from Managers, Directors, Sr. Directors, Vice Presidents, to EV
Career Center | Bolingbrook, IL USA | Production
Tellabs is in need of an individual who will be responsible for working in one or more varying functions within a printed circuit board product assembly process. Duties include automatic insertion, surface mount operation and Surface Mount Technolog
Career Center | Quito, Ecuador | Sales/Marketing,Technical Support
Technical Sales (machinery, animal and plant protection products). Sales Forecast New Products (Bsss Diffusion Model).
Career Center | Delton, Michigan USA | Engineering,Maintenance,Production,Technical Support
IPC Master instructor with a number of years experience in Engineering as well as Machine technician.
1st Place Machinery Inc. | http://www.firstplacemachinery.com/smt_pcb_screen_printers_mpmup100.html
MPM UP100 MPM UP-100 / Sigmanprint MV Stencil Printer Serial # 100834 Year ~ 2000 or newer 20" Stencil Capacity - Pneumatic Stencil locks Type
| https://www.feedersupplier.com/sale-13119451-p3251-mpm-printer-spare-parts-mpm-up2000-vision-card-mpm-p3251-up2000-vision-card.html
P3251 MPM printer SPARE PARTS MPM UP2000 VISION CARD MPM P3251 UP2000 vision card Leave a Message We will call you back soon! Your message must be between 20-3,000 characters