Industry Directory | Manufacturer
Design and manufacture of assembly fixtures
Industry Directory | Manufacturer
As a manufacturer of reflow soldering systems with convection or condensation and drying and coating systems, Rehm Thermal Systems has been producing energy-efficient manufacturing equipment for the electronics and photovoltaics.
A500, A600, A800 - 5, 6 or 8 top/bottom cooling zones. Heating System: Up to eight groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air co
S8, S10, S12 - 8, 10 or 12 top/bottom cooling zones. Heating System: Up to twelve groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air con
Electronics Forum | Tue Mar 09 21:17:10 EST 2004 | gm05688
When soldering a metalized germanimum window to a nickle plated kovar part, I would like to understand the intermetalic. Does the nickle plate actually melt or will the solder(SN63)simple stick to the nickle and not cause nickle to reflow? Any one ou
Electronics Forum | Tue Mar 09 22:26:17 EST 2004 | davef
You should to be soldering to the nickel. The intermetallic is Ni3Sn4. "At relatively low temperatures, the tin-nickel layers form about as rapidly as the tin-copper layers do, but at higher temperatures their growth rate is distinctly lower. At 10
Used SMT Equipment | AOI / Automated Optical Inspection
Hardware composition: Ring LEDs (R, G, B) Image resolution 20µm Fixed shape, fixed substrate Single-phase power supply 100 to 240VAC ±10% The weight is below 500kg Equipment dimensions: 700W×900D×1600H mm (height
Used SMT Equipment | Soldering - Reflow
New arrival, like new condition. Proto-type, small batch LPKF Zelflow R04 Solder Paste Reflow Oven. Very minimal use. Powered up and tested. 220 - 240VAC single phase. FOB: Origin ALSO AVAILABLE: LPKF ZELPRINT LT300 BENCH TOP SOLDER PASTE PRIN
Industry News | 2019-04-30 17:39:40.0
The SMTA Capital Chapter and UP Media Group/Circuits Assembly Magazine are pleased to co-sponsor an amazing Chapter Tutorial Program. The tutorial will be held on June 11 and showcase the latest technologies, designs and reliability trends.
Industry News | 2009-02-03 13:34:04.0
New PCB Rework, Repair, Fabrication Training & Consulting Services.
Technical Library | 2023-01-17 17:58:36.0
Heterogeneous integration has become an important performance enabler as high-performance computing (HPC) demands continue to rise. The focus to enable heterogeneous integration scaling is to push interconnect density limit with increased bandwidth and improved power efficiency. Many different advanced packaging architectures have been deployed to increase I/O wire / area density for higher data bandwidth requirements, and to enable more effective die disaggregation. Embedded Multi-die Interconnect Bridge (EMIB) technology is an advanced, cost-effective approach to in-package high density interconnect of heterogeneous chips, providing high density I/O, and controlled electrical interconnect paths between multiple dice in a package. In emerging architectures, it is required to scale down the EMIB die bump pitch in order to further increase the die-to-die (D2D) communication bandwidth. Aa a result, bump pitch scaling poses significant challenges in the plated solder bump reflow process, e.g., bump height / coplanarity control, solder wicking control, and bump void control. It's crucial to ensure a high-quality solder bump reflow process to meet the final product reliability requirements. In this paper, a combined formic acid based fluxless and vacuum assisted reflow process is developed for fine pitch plated solder bumping application. A high-volume production (HVM) ready tool has been developed for this process.
Technical Library | 2014-06-23 14:50:52.0
It was unusual to see chip terminations change colors when tin lead solders were used but with the introduction of lead free reflow soldering and the corresponding increases in reflow temperatures terminations are now changing colors. Two conditions are present when reflow temperatures are increased for lead free solder alloys that leads to discoloration. Reflow temperatures are above the melting point of tin (Sn MP is 232oC). Air temperatures commonly used in forced convection reflow systems are high enough to both melt the tin plating on the termination allowing it to be pulled into the solder joint due to solder joint liquid solder surface tension leaving behind the exposed nickel barrier. Now those metal oxide colors will be visible due to high air temperatures during reflow.
A500, A600, A800 - 5, 6 or 8 top/bottom cooling zones. Heating System: Up to eight groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air co
S8, S10, S12 - 8, 10 or 12 top/bottom cooling zones. Heating System: Up to twelve groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air con
Career Center | Shen Zhen, China | Management,Sales/Marketing
Working in GLORYPCB for 10 years.knowing electronic supply chain very well. especially for PCB PCBA assembly and other Electronic Manufacturing Service.Glorypcb is a professional electronic manufacturer located in Shenzhen with three facilities.offe
Career Center | Lalkua, India | Engineering,Maintenance,Production,Quality Control,Research and Development,Technical Support
Machine maintenance Service and support knowledge with customer satisfactory. Deal with customers at all level via phone,remote and mail.Sound knowledge of PCB fabrication machine.
SMTnet Express, July 18, 2019, Subscribers: 32,162, Companies: 10,836, Users: 24,951 Via Fill and Through Hole Plating Process with Enhanced TH Microdistribution Credits: MacDermid Inc. The increased demand for electronic devices in recent years
SMTnet Express, November 7, 2019, Subscribers: 32,325, Companies: 10,919, Users: 25,284 Origin and Quantification of Increased Core Loss in MnZn Ferrite Plates of a Multi-Gap Inductor Credits: Power Electronic Systems Laboratory (PES) Inductors