Power NTC thermistor limit inrush current when the power is first turned on, functioning as a power resistor which drops from a high cold resistance to a low hot resistance when heated by the current flowing through, resistance remains negligible low
Lighting Switching PTC Thermistor Description Lighting Switching PTC Thermistor are used when a load in series with the PTC thermistor has to be switched off after a time delay and when switching occurs frequently. A typical application of switching
Electronics Forum | Sun Sep 27 10:42:35 EDT 1998 | l atch
I'm looking for a chart that will help me identify smt resistors and capacitors. I have figured out a few on my own. a resistor with the numbers 510 printed on it was a 51 ohm resistor. numbers 221 was a 220 ohm resistor. numbers 102 was a 1k resis
Electronics Forum | Mon Sep 28 09:18:30 EDT 1998 | Ben Wilmot
The majority of SMT resistors use the following notation. 10 X eg 153 represents 1k5 resistor The third digit in the sequence denotes the number of zeros to add after the first two digits giving the value in ohms. Many Caps will follow the same nota
Industry News | 2010-03-15 11:36:01.0
Going beyond anecdotes and examples of counterfeit parts, this symposium focuses on the solutions that are available and are under development by all sectors of the industry.
Industry News | 2013-03-25 14:58:02.0
IMS has introduced a new type or chip resistor terminal which are non‐magnetic and ultra leach resistant.
Parts & Supplies | SMT Equipment
CAL PIECE A E3622721000 for JUKI750 2050 E36117060A0B REEL HOOK 12 ASM. E3613706A00 REEL_PRESSER_12-56 E3614706A00 REEL SUPPORT SH COLLER E3614706AA0 REEL SUPPORT SH COLLER E3615706A00 REEL_BRAKE E36217210A0 CAL PIECE ASM. (730) E3622721000
Parts & Supplies | SMT Equipment
contact person:banny chen mail:zksale@hysmt.cn skype:miayuan8 best quality & lower price more than we can offer 40000631 CABLE SAFETY B 40000746 CABLE CLAMP X 40001255 SENSOR CABLE GUIDE 50 40001261 SENSOR CABLE GUIDE 60 40001306 CABLE
Technical Library | 1999-08-05 10:34:17.0
This document defines a set of standard test structures with which to benchmark the electrostatic discharge (ESD) robustness of CMOS technologies. The test structures are intended to be used to evaluate the elements of an integrated circuit in the high current and voltage ranges characteristic of ESD events. Test structures are given for resistors, diodes, MOS devices, interconnects, silicon control rectifiers, and parasitic devices. The document explains the implementation strategy and the method of tabulating ESD robustness for various technologies.
Technical Library | 2023-07-25 16:42:54.0
Printing solder paste for very small components like .3mm pitch CSP's and 01005 Chip Components is a challenge for the printing process when other larger components like RF shields, SMT Connectors, and large chip or resistor components are also present on the PCB. The smaller components require a stencil thickness typically of 3 mils (75u) to keep the Area Ratio greater than .55 for good paste transfer efficiency. The larger components require either more solder paste height or volume, thus a stencil thickness in the range of 4 to 5 mils (100 to 125u). This paper will explore two stencil solutions to solve this dilemma. The first is a "Two Print Stencil" option where the small component apertures are printed with a thin stencil and the larger components with a thicker stencil with relief pockets for the first print. Successful prints with Keep-Outs as small as 15 mils (400u) will be demonstrated. The second solution is a stencil technology that will provide good paste transfer efficiency for Area Ratio's below .5. In this case a thicker stencil can be utilized to print all components. Paste transfer results for several different stencil types including Laser-Cut Fine Grain stainless steel, Laser-Cut stainless steel with and w/o PTFE Teflon coating, AMTX E-FAB with and w/o PTFE coating for Area Ratios ranging from .4 up to .69.
https://www.ascen.ltd/Products/Component_lead_forming_machine/ Motorized version ASCEN taped component axial lead forming machine AS-809F axial lead former, use for cut and bend axial components braid resistor,capacitor, inductor, diode and other ele
https://www.ascen.ltd/Products/Component_lead_forming_machine/ Motorized version ASCEN taped component axial lead forming machine AS-809F axial lead former, use for cut and bend axial components braid resistor,capacitor, inductor, diode and other ele
High Voltage Chip Resistors High Voltage Chip Resistors Many component engineers are faced with a circuit requirement calling for resistors having voltage ratings well above that associated with surface mount chip resistors, but below the level
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/resistor-color-bands_topic1869_post7630.html
: 5011 Post Options Post Reply Quote Tom H Report Post Thanks(0) Quote Reply Posted: 11 May 2016 at 7:13am In V2016.04 you can change the colors to the resistor bands for Axial Lead parts
KingFei SMT Tech | https://www.smtspare-parts.com/sale-11928465-manual-type-resistor-lead-cutting-and-forming-machine-radial-capacitor-lead-cutting-machine.html
Manual Type Resistor Lead Cutting And forming Machine Radial Capacitor Lead Cutting Machine Leave a Message We will call you back soon