Industry Directory | Distributor / Manufacturer
An international distributor of mechanical IC samples or "dummy" components, SMD production tools and equipment
Industry Directory | Consultant / Service Provider / Manufacturer
Specializing in electronic circuit board assembly services. Various capabilities include engineering, assembly, designing, prototyping,supply chain management, testing, documentation, rework, repair and soldering. On-time delivery
New Equipment | Solder Materials
We have a wide variety of flux-Cored solder, a mix of metal alloy, flux and other elements, that we have put together to match every type of application. This formula is designed so that the incidence of bridging is rare; likew
New Equipment | Solder Paste Stencils
EasyBraid’s stencil rolls are designed for use in SMT screen printing lines which keep stencil apertures clear of paste residues during the automatic screen printing process. They also clean the bottom of stencils, keeping them free from paste and fl
Electronics Forum | Fri Sep 17 03:03:29 EDT 2010 | grahamcooper22
Hi Gani, looking at the HASL icture and the poor wetting of the solder over the pads I would imagine that the HASL coating is very thin on the pads and in actual fact isn't 'solder' but is tin /copper intemetallic and this has poor solderability. It
Electronics Forum | Mon Apr 26 17:12:14 EDT 2004 | babe
Take a solder iron with some wire solder and attempt to tin the leads of the component. Look under magnifier or microscope. Did they wet? If not try fluxing them with liquid flux and then soldering again. Did they wet? If they did not then you may wa
Used SMT Equipment | SPI / Solder Paste Inspection
The LSM300 follows the successful Laser section Microscopes LSM and LSM2. This new non-contact laser based system is an off-Line solder paste inspection system.LSM300 provides automatic height measurements, eliminating the inconsistencies of manual m
Industry News | 2023-03-16 14:31:59.0
The SMTA is pleased to announce the Best Papers from SMTA International 2022. The winners were selected by members of the conference technical committee. For these exceptional achievements, a plaque is given to primary authors of all winning papers.
Industry News | 2011-08-17 12:59:10.0
The SMTA announced that SMTA International will provide updated research on Head-in-Pillow component soldering defects as well as a focused tutorial on the subject. SMTAI will take place October 16-20, 2011 in Ft. Worth, Texas.
Technical Library | 2022-10-31 17:25:37.0
Mixed formulation solder alloys refer to specific combinations of Sn-37Pb and SAC305 (96.5Sn–3.0Ag–0.5Cu). They present a solution for the interim period before Pb-free electronic assemblies are universally accepted. In this work, the surfaces of mixed formulation solder alloys have been studied by in situ and real-time Auger electron spectroscopy as a function of temperature as the alloys are raised above the melting point. With increasing temperature, there is a growing fraction of low-level, bulk contaminants that segregate to the alloy surfaces. In particular, the amount of surface C is nearly _50–60 at. % C at the melting point. The segregating impurities inhibit solderability by providing a blocking layer to reaction between the alloy and substrate. A similar phenomenon has been observed over a wide range of (SAC and non-SAC) alloys synthesized by a variety of techniques. That solder alloy surfaces at melting have a radically different composition from the bulk uncovers a key variable that helps to explain the wide variability in contact angles reported in previous studies of wetting and adhesion. VC 2011 American Vacuum Society. [DOI: 10.1116/1.3584821]
Technical Library | 2021-07-06 21:13:36.0
The surface finishes commonly used on printed circuit boards (PCBs) have an effect on solder paste performance in the surface mount process. Some surface finishes are non-planar like hot air solder level (HASL) which can lead to inconsistencies in solder paste printing. Other surface finishes are difficult to wet during reflow like organic solderability preservative (OSP). What is the overall effect of surface finish on solder paste performance? Which solder paste is best for each surface finish? It is the goal of this paper to answer these questions.
DescriptionThe Electrovert® Electra™ is an advanced, meticulously engineered wave soldering system designed for high-mass and high-volume manufacturers. Although intended for maximum throughput requirements, the Electra also offers maximum process fl
With the Spectrum II's new Precision Z-axis, smaller dots and thinner solder paste lines can be achieved. This capability is standard on all Spectrum II systems and replaces the Precision Z option on the older Axiom products. In order to achieve su
Training Courses | | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Career Center | Wesley Chapel, Florida USA | Engineering,Management,Quality Control
15 years of experience on Electronic Manufacturing. Certified SMT Process Engineer TQM Knowledge Statistics DOE Screen Printer Thermal Process Knowledge JIT International Project Engineering Experience
Career Center | , | Engineering,Production
Project Management, SMT Process Engineering
GPD Global | https://www.gpd-global.com/lead-free-solder-paste-dispensing.php
Lead Free Solder Paste Dispensing, Leaded Solder Paste Dispensing Home Products Fluid Dispensing Equipment High Precision Dispenser - MAX Series Large Format Board Dispensing - DS Series Table Top Dispensing Equipment Loader
| https://www.eptac.com/blog/are-voids-in-solder-joints-really-an-issue
. This is data, not anecdotal evidence, so we should pay attention. Voids are truly a phenomenon in liquid physics, where you have two liquids, molten solder and some other non-metallic liquid, such as flux and carrying vehicles