Industry Directory | Manufacturer
PCB Repairs of all kinds including-Solder on Tab (Solder Removal, Gold Plating), PTH & Delam repairs, etc.
Industry Directory | Manufacturer
Ball Grid Array IC Reconditioning, Re-Ball Service, BGA IC Purchase and Resale
KSUN R05 JUKI Feeder Calibration It is essential for this equipment that enhanced productivity , installation and quality improvement As the high efficiency vision camera is asked in order to investigate precisely and repair the error of device pos
New Equipment | Rework & Repair Equipment
Pin Grid Array Extractors are available in two sizes and provide a quick and safe way to extract Pin Grid Array components from their sockets. All component sizes can be accommodated, as the tool is available in two or four grip models. Adjusting the
Electronics Forum | Tue May 16 15:53:09 EDT 2006 | Manvendra Verma
What is the solution for removing epoxy on BGA ics?
Electronics Forum | Sun May 21 09:38:25 EDT 2006 | davef
Epoxy Removal and IC Delidding [Hardware Hacking: Have Fun While Voiding Your Warranty, Chapter 14] Encapsulation of critical components using epoxy or other adhesives is commonly done to prevent tampering and device access (the microprocessor shown
Used SMT Equipment | Pick and Place/Feeders
Detailed Product Description 1. The acquisition for the rectangular coordinate of X-Y direction. 2. Check for the existence, transformation, user in the feeder 3. The installation is to euip it with actual device and consolidation in feeder base
Used SMT Equipment | Pick and Place/Feeders
Concept: Over drive motion Ultimate access Super wide range DDH V5 Smart operation Voluntary line operation Wide open &Easy access Quick exchange Auto changeover PP type LISA Feeder hot swap Chip theory speed 84500chip Placement ra
Industry News | 2010-09-22 15:01:40.0
Removing heat has become a major issue in the electronics industry as more highly integrated devices are jammed into less space and as high power devices, such as LEDs, become increasingly more common.
Industry News | 2022-11-11 07:33:41.0
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board pads.
Parts & Supplies | Pick and Place/Feeders
GIC-F01 FUJI NXT Feeder Calibration JIG It is essential for this equipment that enhanced productivity , installation and quality improvement As the high efficiency vision camera is asked in order to investigate precisely and repair the error of
Parts & Supplies | Pick and Place/Feeders
GIC-Y01 YAMAHA Feeder Calibration JIG It is essential for this equipment that enhanced productivity , installation and quality improvement As the high efficiency vision camera is asked in order to investigate precisely and repair the error of de
Technical Library | 2014-05-12 09:24:11.0
With the advancement of the electronic industry, Package on package (POP) has become increasingly popular IC package for electronic devices, particularly in mobile devices due to its benefits of miniaturization, design flexibility and cost efficiency. However, there are some issues that have been reported such as SIR drop due to small gap between top and bottom components, difficulty underfilling and rework due to stacked IC components and process yield issues. Some suppliers have reported using some methods such as dipping epoxy paste or epoxy flux to address these issues, but so far, no customer has reported using these methods or materials in their mass production. In order to address these issues for POP assembly, YINCAE has successfully developed a first individual solder joint encapsulant adhesive.
Technical Library | 2014-06-02 11:03:45.0
With the advancement of the electronic industry, package on package (POP) has become increasingly popular IC package for electronic devices, particularly POP TMV (Through Mold Vials) in mobile devices due to its benefits of miniaturization, design flexibility and cost efficiency. However, there are some issues that have been reported such as SIR drop due to small gap between top and bottom components, difficulty underfilling and rework due to stacked IC components and process yield issues. Some suppliers have reported using some methods such as dipping epoxy paste or epoxy flux to address these issues, but so far no customer has reported using these methods or materials in their mass production. In order to address these issues for POP TMV assembly, YINCAE has successfully developed and commercialized the first individual solder joint encapsulant adhesive for mass production for years.
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
ETA LED Laser Marking Machine If you could not find any similar items you want, you may send some photos to us. because our catalog and website haven't included all of our products. LED Laser Marking Machine,Led Bulb Laser Machine,LED Bulb Fi
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | | | IPC-7711/7721 Specialist (CIS)
The Certified IPC-7711/7721 Specialist (CIS) training focuses on rework of electronic assemblies and repair and modification of printed boards and electronic assemblies.
Career Center | Santa Cruz, California USA | Production,Quality Control
Soldering Technician, Touch-up for PCBAs Perform hand soldering and touch-up rework for Printed Circuit Board Assemblies (PCBA), cables and associated equipment. Inspect PCBA for defects, loose connections, missing components. Solder to perform r
Career Center | Alta Loma, California | Engineering,Quality Control,Research and Development
Rigid and Flexible Printed Circuits Plating and Metal Finishing Operations Six Sigma Work Instruction Documentation Process Development Equipment Selection and Specification New Facility Startup Air, Water and Hazardous Waste Environmental Reporting
Career Center | ORLANDO, Florida USA | Engineering,Maintenance,Production,Technical Support
Manufacturing tech/eng for a contract manufacture for 10+ years. Been working in the SMT industry for a total of 20yrs. Have done everything from operator to process work. Most familiar with Assembleon, MPM, DEK, BTU,Electrovert, SLIM-KIC, SUPER-MOLE
3D ICs With TSVs - Design Challenges And Requirements Heat Management in Printed Circuit Boards This report discusses the significance of heat management in the design of printed circuit boards (PCB).After an introduction into the basics of PCBs
Imagineering, Inc. | https://www.pcbnet.com/blog/high-temperature-pcb-considerations-for-high-heat-applications/
) is greater than 170°C. The glass transition temperature is one of the most important properties of any epoxy, representing the temperature which the polymer transition from a hard material to a soft one
| https://www.eptac.com/faqs/ask-helena-leo/ask/the-difference-between-touch-up-rework-and-repair
. As this statement indicates that the final product will not look like the original unit as signs of some work will be visible. An example of this would be a burnt hole in a board which has been fixed by removing the burnt area and refilling it with epoxy and such
winsouce.jpg)
.gif)