New Equipment | Rework & Repair Equipment
BGA Rework Stations from the BGA Experts with over 25 years rework process experience and customer support! For high volume BGA Rework on even the largest computer and networking boards! The model SV560A has a high resolution optical system for pla
Inclusions/voids will be reduced up to 99% Vacuum process can be switched on or off Nitrogen and air soldering possible Double sided PCB possible Pass through height: 30 mm (top and bottom) Small PCB with carrier Setting parameter: Time until sub-pre
Electronics Forum | Fri Mar 30 06:59:00 EDT 2018 | bobpan
In Production Monitor....there is Utility and Axis speed. Make sure the z-axis are set to 100%. I would also check to make sure in your component information that you dont have your parts slowed down or have long place and/or pick delays. good luck
Electronics Forum | Tue Aug 23 03:29:37 EDT 2022 | samhe
I received a buck-boost DCDC board with an optical sensor from NextPCB, so I mounted the components and measured the efficiency. Table of contents Board received from NextPCB Solder paste printing Mounting of parts Reflow operation check Attaching
Used SMT Equipment | General Purpose Equipment
Year 2008 - Like New Condition Tyco SEP 3T Shuttle Electric Press Standalone electric press for the application of PCBs onto compliant pin housings or connectors • Servo electric press with shuttle system for product location under press ram • Ho
Used SMT Equipment | Pick and Place/Feeders
Concept: Over drive motion Ultimate access Super wide range DDH V5 Smart operation Voluntary line operation Wide open &Easy access Quick exchange Auto changeover PP type LISA Feeder hot swap Chip theory speed 84500chip Placement ra
Industry News | 2011-09-12 15:42:18.0
For the past year, engineers from companies like Honeywell Aerospace and Rockwell Collins have been meeting to lay the groundwork for IPC-A-630, Requirements and Acceptance for Enclosures, better known as “the box build standard.” These volunteers have come largely from the OEMs that specify the cabinetry they will use.
Industry News | 2016-02-16 11:59:42.0
Count On Tools will exhibit in Booth #2801 at the 2016 IPC APEX EXPO, scheduled to take place March 15-17, 2016 at the Las Vegas Convention Center. Company representatives will celebrate COT’s 25-year anniversary with several promotions and giveaways. Additionally, the IPC APEX EXPO will mark the official launch of the QWIKTRAY program for the U.S. market.
 teaching box for SM421,411 (2)_11.jpg)
Parts & Supplies | Pick and Place/Feeders
Spot sale of the following Samsung accessories / original Feeders Samsung Flying up, Samsung 12MM Feeder, Samsung 12mm FEEDER, Samsung 45 12mm Feeder CP Series: 8 * 2MM, 8 * 4MM, 12MM, 16MM, 24MM, 32MM, 44mm, 56mm Feeder CP vibration Feeder; IC tr
Parts & Supplies | Pick and Place/Feeders
KM1-M4592-11X VAC SENSOR BOARD ASSY KM1-M4592-12X KM1-M4592-11X KM1-M4592-13X Vacuum Test Board Vacuum Sensor Board VAC SENSOR BOARD ASSYOther yamaha part: YAMAHA vacuum test board / vacuum induction board / vacuum board / vacuum board / VAC SENSOR
Technical Library | 2019-01-20 22:47:35.0
With the rapid development of the electronics industry, more and more components such as integrated circuits and connectors, relays, power modules, etc. need to be packaged with IC tubes. The anti static ic tubes is actually a kind of pvc plastic(reference to : What are the materials for IC tubes) profile, the size varies with the shape of the installed product, the precision requirement is high, the wall thickness should be controlled within ±0.1mm, and the surface is required to have no impurity spots, smooth and transparent. The IC packaging tubes produced by Sewate Technology Co., Ltd. are extruded. The typical process flow is: extrusion, vacuum adsorption setting, traction, fixed length cutting and directional discharge, deburring, immersion antistatic liquid, drying, testing, packaging and storage
Technical Library | 2020-12-29 20:55:46.0
Voiding in solder joints has been studied extensively, and the effects of many variables compared and contrasted with respect to voiding performance. Solder paste flux, solder powder size, stencil design, circuit board design, via-in-pad design, surface finish, component size, reflow profile, vacuum reflow, nitrogen reflow and other parameters have been varied and voiding quantified for each. The results show some differences in voiding performance with respect to most of these variables but these variables are not independent of each other. Voiding in solder joints is a complex issue that often requires multiple approaches to reduce voiding below required limits. This paper focuses on solutions to voiding for commonly used bottom terminated components (BTCs).
PCB magazine loader and PCB magazine unloader loading orunloading the PCB board on assembly line, check the detial for: https://www.ascen.ltd/Products/Automatic_SMT_equipment/PCB_loader/87.html multi magazine PCB loader is used at the starting of the
PCB magazine loader and PCB magazine unloader loading orunloading the PCB board on assembly line, check the detial for: https://www.ascen.ltd/Products/Automatic_SMT_equipment/PCB_loader/87.html multi magazine PCB loader is used at the starting of the
Career Center | cabuyao, Philippines | Engineering
I had 9 years working as a technician starting in Smart electronic)as Mainline Technician. SGIC(Sanritsu Great International Corporation) as SMT mainline Techinician and IMI (Integrated Micro-Electronics INC,)as SMT Process Technician.
Career Center | San Pablo City, Laguna, Philippines | Engineering,Maintenance,Production,Sales/Marketing,Technical Support
Some key points you may find relevant to this job opportunity include: Extensive experience and knowledge on Service and Technical skills by performing Set-up, Buy-off, troubleshooting of the assigned Equipments. Provide solution to custom
| http://etasmt.com/te_news_bulletin/2020-08-19/18761.chtml
. The increase in the assembly density of electronic products and the reduction in the size of components and their pin spacing have made the soldering process of SMA more difficult, and the setting
Heller Industries Inc. | https://hellerindustries.com/heller/vacuum-profile-reflow/
How To Set Up Vacuum Assisted Reflow Profile Home » Heller Blog » Tips for Setting Up an Optimized Vacuum Profile when Using Vacuum Assisted Reflow Tips for Setting Up an Optimized Vacuum Profile when Using Vacuum Assisted Reflow With
A global industrial auction and valuation business with extensive experience in SMT, PCB Assembly & Manufacturing, Test, Semiconductor and other Electronics Machinery & Equipment.
Manufacturer / Equipment Dealer / Broker / Auctions
896 Main Street
Branford, CT USA
Phone: 203-488-7020
.gif)
