Industry Directory | Consultant / Service Provider / Manufacturer
Gen3 Systems is a specialist manufacturer of test and measurement equipment used to help predict reliability of electronic circuits and systems in the field.
Industry Directory | Distributor / Manufacturer / Manufacturer's Representative
North American Distributor for GEN3 Systems Ltd.test equipment and reliability products, and Inspectis HD Camera inspection tools.
New Equipment | Test Equipment
Localized Electronics Cleanliness Tester and Residue Extractor The information gathered when using the C3 is intended to provide a measure of the cleanliness of a localized region of a circuit board. In addition, the C3 extracts a sample of the effl
Electronics Forum | Mon Dec 20 10:20:14 EST 2010 | 18424
Test Resistance to ECM shall be 65C +- 2C @ 88.5% +- 3.5% All SIR Measurements shall not exceed 100 MOhm. I am not sure of voltage.
Electronics Forum | Tue Jun 12 13:53:43 EDT 2001 | Eliud Rivera
We are trying to quilify a No-Cclean solder paste and we would like to know what kind of criterias or measurments are use to qualify the amount residues? Can we use an omega meter for that? What equipment measures SIR?
Industry News | 2016-11-30 14:47:45.0
ACI Technologies invites you to download a free copy of its very popular e-booklet, “Failure Analysis Techniques for Electronics” from its Website store, which is located at http://store.aciusa.org/Failure-Analysis-Techniques-for-Electronics-Digital-Download-P181.aspx
Industry News | 2012-12-03 19:52:39.0
Printed Board Assembly Cleaning and Contamination Testing Center marks its debut at IPC APEX EXPO®, February 19–21, 2013, at the San Diego Convention Center.
Technical Library | 2015-02-27 16:46:30.0
During the last period of newly assembled electrical devices (pcbs), new component types like LGA and QFN were also qualified as well as smaller passive components with reliability requirements based on the automotive and industrial industry. In the narrow gaps under components, residues can accumulate more by the capillary forces. This is not that much a surface resistance than an interface issue. Also that the flux residues under such types of components creates interaction with the solder resists from the pcb, as well as the component body was not completely described in the standard SIR measurement. On the other hand also, electrical influence with higher voltage creates new terms and conditions, in particular the combination of power and logic in such devices. The standard SIR measurement cannot analyze those combinations.The paper will discuss the requirements for a measurement process, and will give results. The influences of the pcb and component quality will also be discussed. Furthermore it will describe requirements for nc solder paste to increase the chemical/thermical/electrical reliability for whole devices
Technical Library | 2017-07-13 16:16:27.0
Controlled humidity and temperature controlled surface insulation resistance (SIR) measurements of flux covered test vehicles, subject to a direct current (D.C.) bias voltage are recognized by a number of global standards organizations as the preferred method to determine if no clean solder paste and wave soldering flux residues are suitable for reliable electronic assemblies. The IPC, Japanese Industry Standard (JIS), Deutsches Institut fur Normung (DIN) and International Electrical Commission (IEC) all have industry reviewed standards using similar variations of this measurement. (...) This study will compare the results from testing two solder pastes using the IPC-J-STD-004B, IPC TM-650 2.6.3.7 surface insulation resistance test, and IPC TM-650 2.3.25 in an attempt to investigate the correlation of ROSE methods as predictors of electronic assembly electrical reliability.
ST New and Original STM32F072CBT6 in Stock LQFP-48 package ST New and Original STM32F072CBT6 in Stock LQFP-48 package ST New and Original STM32F072CBT6 in Stock LQFP-48 package SI1539CDL-T1-GE3 VISHAY SI2300 VISHAY SI2301 VISHAY SI2302 VISHAY
TI New and Origina SN6501DBVR in Stock ICSOT23-5, 2022+ package SN6501DBVR Low Noise 350mA, 410kHz Transformer Driver for Isolated Power Today's Hot Deals: SSM3K35AFS SOT-523 TOSHIBA 17+ RZM001P02T2L SOT-723 ROHM 22+ MMSS8550-H-TP SOT-23 MCC
Career Center | , | 2013-03-07 05:50:27.0
Looking for Leader ship Opprtunity in Electronics Manufacturing Plant in India
SMTnet Express, February 6, 2014, Subscribers: 26500, Members: Companies: 13567, Users: 35716 Understanding SIR by Chris Nash, Eric Bastow; Indium Corporation Many electronics manufacturers perform SIR testing to evaluate solder materials
SMTnet Express, July 13, 2017, Subscribers: 30,584, Companies: 10,624, Users: 23,496 Divergence in Test Results Using IPC Standard SIR and Ionic Contamination Measurements K. Tellefsen, M. Holtzer, T. Cucu, M. Liberatore, M. Schmidt - Alpha
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/ko-kr/divisions/efd/resources/solder-selection-guide
Adhesive Dispensing Systems Nordson EFD Nordson ELECTRONICS SOLUTIONS Industrial Coating Systems Nordson MEASUREMENT & CONTROL Nordson MEDICAL Polymer Processing Systems Nordson TEST & INSPECTION 자료실 뒤 자료실 브로셔, 카탈로그 또는 운영 매뉴얼을 찾고 있든 상관없이 당사의 리소스 라이브러리에는 필요한