Industry Directory | Manufacturer
Manufacturer of Laser Cut & Chemical Etched Stencils.
New Equipment | Solder Paste Stencils
Step-up / Step-down Stencil. The patented step stencil from LaserJob, called PatchWork® - stencil, was developed to print in one printing step different paste deposit heights. Due to the multiplicity of different component leads on one printed circu
New Equipment | Solder Paste Stencils
Through the increase of mixed technologies, stepped stencils have gained importance to the electronic assembly manufacturer. If the solder paste quantity can no longer be adequately regulated by adjusting Step/Relief Stencil Picture the pad sizes, st
Electronics Forum | Wed Jan 27 02:07:25 EST 2021 | davef
IPC-7525 does a good job of giving guidelines for designing stencils, including stepped stencils
Electronics Forum | Mon Nov 25 12:32:20 EST 2002 | davef
Now that is a BIG step. Stencil type: * A metal squeegee is fine with stepped stencils. * A rubber squeegee is fine with stepped stencils. Comments on step stencil "keepouts" are: * Use an ample space around the stepped down component pads that is
Industry News | 2012-06-09 14:33:06.0
To help designers and board assemblers address the challenges of working with new materials and smaller, finer-pitch components, IPC – Association Connecting Electronics Industries® released the B revision of IPC-7525, Stencil Design Guidelines.
Industry News | 2013-06-26 09:09:19.0
The SMTA announced Harald Grumm from Christian Koenen GmbH as the recipient of the Best of Conference Award for his presentation “The Potential of Stencil Technology – Choosing the Right Stencil Options to Maximize Yield and Earnings” at the 9th Annual International Conference on Soldering and Reliability, held May 14-17, 2013 at the Sheraton Toronto Airport, Ontario, Canada.
Technical Library | 2023-07-25 16:50:02.0
Some of the new handheld communication devices offer real challenges to the paste printing process. Normally, there are very small devices like 01005 chip components as well as 0.3 mm pitch uBGA along with other devices that require higher deposits of solder paste. Surface mount connectors or RF shields with coplanarity issues fall into this category. Aperture sizes for the small devices require a stencil thickness in the 50 to 75 um (2-3 mils) range for effective paste transfer whereas the RF shield and SMT connector would like at least 150 um (6 mils) paste height. Spacing is too small to use normal step stencils. This paper will explore a different type of step stencil for this application; a "Two-Print Stencil Process" step stencil. Here is a brief description of a "Two-Print Stencil Process". A 50 to 75 um (2-3 mils) stencil is used to print solder paste for the 01005, 0.3 mm pitch uBGA and other fine pitch components. While this paste is still wet a second in-line stencil printer is used to print all other components using a second thicker stencil. This second stencil has relief pockets on the contact side of the stencil any paste was printed with the first stencil. Design guidelines for minimum keep-out distances between the relief step, the fine pitch apertures, and the RF Shields apertures as well relief pocket height clearance of the paste printed by the first print stencil will be provided.
Technical Library | 2015-08-25 13:51:27.0
The stencil printing process is one of the most critical processes in the electronic production. Due to the requirement: "faster and smaller" it is necessary to place components with different paste volume close together without regard to solder paste printing. In our days it is no longer possible to control the solder paste volume only by adjustment of the aperture dimensions. The requirements of solder paste volumes for specific components are realized by different thicknesses of metal sheets in one stencil with so called step stencils. The step-down stencil is required when it is desirable to print fine-pitch devices using a thinner stencil foil, but print other devices using a thicker stencil foil. The paper presents the innovative technology of step-up and step-down stencils in a laser cutting and laser welding process. The step-up/step-down stencil is a special development for the adjustment of solder paste quantity, fulfilling the needs of placement and soldering. This includes the laser cutting and laser welding process as well as the resulting stencil characteristics and the potential of the printing process.
ALPHA® TETRABOND™ is the culmination of "frameless" stencil development; an elegantly simple system designed to enhance the rigidity of the foil, making safe mounting and demounting an easier proposition. Innovatively encompassed in a thin, one piece
SMT Stencil Production with the LPKF StencilLaser G 6080 The LPKF StencilLaser G 6080 is a highly productive and precise SMT stencil laser cutting system. Learn more: http://www.lpkf.com/products/smt-stencils/cutting-smt-stencils-and-microparts.htm?u
Career Center | Bangalore, India | Engineering,Maintenance,Production,Technical Support
SMT Stencil designing & Knowledge of full SMT process software known CAD/CAM -circuit CAM Pro 7.3,GC Power station, GCCAM Edit,Auto CAD, Fault finding of Electronic Boards & Servicing electronic machines.
| https://pcbasupplies.com/technicians-aids/
Technician's Aids Desoldering Braid Lead Free One Step Quick Braid Sea Braid Stencil Wipes Shop By Brand Count On Tools Thermaltronics EasyBraid BEAU TECH Tronex XDry Corp PCBASupplies View all
| https://www.smtfactory.com/a-beneficial-step-to-deepen-global-cooperation.html
A Beneficial Step to Deepen Global Cooperation - I.C.T SMT Machine English Bahasa indonesia Сербия Česky Dansk Deutsch Español Français Hrvatski Italiano magyar Nederlands Polski
.gif)
