Industry Directory | Manufacturer
We manufacture of a variety of Terminal block as per custom design & specifications. The range of Terminal Blocks includes Brass Terminal Blocks, PCB Terminal Blocks, Heavy Duty Terminal Blocks, DIN Rail Terminal Blocks and more.
Industry Directory | Manufacturer / Other
Importer/distributor/manufacturer of connectors
New Equipment | Cable & Wire Harness Equipment
Low Cost Table Top Crimp Machine. The C 200 is a table top low cost crimp tool which takes a variety of dies from different manufacturers. Air operated using standard factory air (5 bar min), with a pressing capacity of up to 1,200 kp, this portable
Brass Neutral Link manufacture and export Brass Terminal Blocks including Brass Battery Terminals, Copper Terminal Blocks, Punch Terminal, Brass Screw Terminal Block, PCB Terminal Block, Connector Terminal Block, Brass Blade Terminals. Our Brass Term
Electronics Forum | Sat Jul 19 12:22:55 EDT 2008 | operator
Are there any softwares OR functions inside of the softwares that allow a designer that is creating a very large complicated wiring diagram with say....many terminal blocks and connectors etc... to run a point to point check on his drawing? Bascially
Electronics Forum | Wed Jul 11 14:44:33 EDT 2007 | cyber_wolf
Ya I found that out while pulling the motor wires out of the terminal blocks.
Used SMT Equipment | In-Circuit Testers
Description The Agilent 34970A Data Acquisition / Data Logger Switch Unit consists of a three-slot mainframe with a built-in 6 1/2 digit digital multimeter. Each channel can be configured independently to measure one of 11 different functions withou
Used SMT Equipment | In-Circuit Testers
* Bumpers and Handles Included* Features 3-slot mainframe with built-in GPIB and RS232 interfaces 6 1/2-digit (22-bit) internal DMM, scanning up to 250 channels per second 8 switch and control plug-in modules to choose from Built-in signal condi
Industry News | 2003-05-08 07:27:27.0
Easby Electronics is offering a line of low-cost plug and socket PCB terminal blocks in a vast range of styles and sizes, which now include 3.50 and 3.81mm pitches.
Industry News | 2003-04-14 08:50:52.0
Providing connection facilities for PCBs designed to be used in hazardous areas is straightforward with Phoenix Contact's new range of Combicon Ex-approved printed circuit terminal blocks.
Parts & Supplies | SMT Equipment
USE ALTENATIVE PART > u FUJI S5120A SWITCH PHOTO FUJI S5124A SWITCH PHOTO FUJI S5125A SWITCH PHOTO FUJI S5126A SWITCH PHOTO FUJI S5128A SWITCH PHOTO FUJI S5129A SWITCH PHOTO FUJI S5133A SWITCH PHOTO FUJI S5134A SWITCH PHOTO FUJI S51
Parts & Supplies | Pick and Place/Feeders
USE ALTENATIVE PART > u FUJI S5120A SWITCH PHOTO FUJI S5124A SWITCH PHOTO FUJI S5125A SWITCH PHOTO FUJI S5126A SWITCH PHOTO FUJI S5128A SWITCH PHOTO FUJI S5129A SWITCH PHOTO FUJI S5133A SWITCH PHOTO FUJI S5134A SWITCH PHOTO FUJI S5135A SWITCH PHOTO F
Technical Library | 2020-11-24 23:01:04.0
The miniaturization trend is driving industry to adopting low standoff components or components in cavity. The cost reduction pressure is pushing telecommunication industry to combine assembly of components and electromagnetic shield in one single reflow process. As a result, the flux outgassing/drying is getting very difficult for devices due to poor venting channel. This resulted in insufficiently dried/burnt-off flux residue. For a properly formulated flux, the remaining flux activity posed no issue in a dried flux residue for no-clean process. However, when venting channel is blocked, not only solvents remain, but also activators could not be burnt off. The presence of solvents allows mobility of active ingredients and the associated corrosion, thus poses a major threat to the reliability. In this work, a new halogen-free no-clean SnAgCu solder paste, 33-76-1, has been developed. This solder paste exhibited SIR value above the IPC spec 100 MΩ without any dendrite formation, even with a wet flux residue on the comb pattern. The wet flux residue was caused by covering the comb pattern with 10 mm × 10 mm glass slide during reflow and SIR testing in order to mimic the poorly vented low standoff components. The paste 33-76-1 also showed very good SMT assembly performance, including voiding of QFN and HIP resistance. The wetting ability of paste 33-76-1 was very good under nitrogen. For air reflow, 33-76-1 still matched paste C which is widely accepted by industry for air reflow process. The above good performance on both non-corrosivity with wet flux residue and robust SMT process can only be accomplished through a breakthrough in flux technology.
Contact Us Sales manager: Mac Xie Mobile: +8618020714662(WhatsApp) Email: at@mooreplc.com Skype: +8618020714662 Contact Us ✭Product Overview✭ Brand GE Fanuc Series PACSystem RX3i Manufacturer GE Fanuc Manufacturer GE Intelligent Platfor
Sales manager: Mac Xie Mobile: +8618020714662(WhatsApp) Email: at@mooreplc.com Skype: +8618020714662 Product Detail ManufacturerWAGO Corporation Manufacturer Product Number280-905 Description2-CONDUCTOR THROUGH TERMINAL BLO Detailed Descr
Events Calendar | Wed Apr 21 00:00:00 EDT 2021 - Wed Apr 21 00:00:00 EDT 2021 | ,
Oregon Chapter Tutorial: How Clean is Clean and How Do You Know for Sure?
Career Center | , Philippines | Engineering,Technical Support
Electronic manufacturing and Semiconductor equipment programming, sustenance and preventive maintenance. Knowledge in PLC, pneumatics and automated equipment. Desktop, Laptop computer servicing trouble-shooting, repair, hardware and software instal
Career Center | Singapore, Singapore | Engineering,Production
I am a result/goal-oriented engineer with 20 years of experience in Surface Mount Technology (SMT) environment, of which 7 years were heavily involved in field service and field application for Automated Optical Inspection (AOI) machines. I partici
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/body-outline-in-designer_topic3203.html
: 4 Post Options Post Reply Quote kmiha Report Post Thanks(0) Quote Reply Topic: Body Outline in Designer Posted: 06 Dec 2022 at 3:05pm I used the Designer to make a series of terminal blocks of 2,3,4,5
Heller 公司 | https://hellerindustries.com.cn/part/5534/
5534 » Parts » 5534 5534 : Terminal Blocks Beige 145 AMP UL Part Name: Terminal Blocks Beige 145 AMP UL Part #:5534 Contact Us About