Industry Directory | Manufacturer
The international full service manufacturer of systems, detergents, equipment and process design for the cleaning in electronics production.
The pressure meter comes in the same available formats as the pH meters in either a DIN box or a bright polish finished IP65 rated desktop enclosure. The meter can be connected to either one or two pressure flow cells at one time. The flow cell desig
The best stability under all operating conditions is achieved by electrical rotary equipment (motors and generators) and static electrical equipment (transformers and sensors) if all the air trapped inside the wire windings is replaced with insulatio
Electronics Forum | Wed Sep 29 09:29:47 EDT 2010 | swag
Take a few parts from the reel and look close at the parts to make sure the bottom surface of the leads is below the bottom surface of the body.
Electronics Forum | Wed Sep 29 08:26:03 EDT 2010 | babe7362000
We are Currently running a Board and it seems that the SOT-223's on the bottom side have flux and water trapped under the part. Nothing has changed in our process and this is the only board that it is happening on. We are using Kester R562 water wa
Used SMT Equipment | Soldering - Reflow
hh 5 independent controlled heating zones hh Internal cooling zone hh Integrated Ioniser for ESD safe soldering hh DIMAsoft reflow profiler software available hh Flux traps to minimize contamination of the system hh Easy to service one way appro
Used SMT Equipment | Soldering - Reflow
hh 5 independent controlled heating zones hh Internal cooling zone hh Integrated Ioniser for ESD safe soldering hh DIMAsoft reflow profiler software available hh Flux traps to minimize contamination of the system hh Easy to service one way appro
Industry News | 2012-05-11 20:35:45.0
Heller Industries has been awarded a 2012 SMT VISION Award in the category of Soldering Reflow for its 1936 Mark 5 Reflow Oven. The award was presented on April 25, 2012 at the Nepcon China Exhibition.
Industry News | 2012-02-15 19:18:44.0
GPD Global announces that its PCD4H Dispense Pump yields excellent results with phosphor and non-phosphor-filled LED encapsulation as viewed on the color chart by tightly grouped results.
Parts & Supplies | Assembly Accessories
Advantages of KIC START Cheap price. The temperature curve can be drawn quickly and accurately. Immediate and objective temperature curve analysis Easy to use software Manual temperature curve prediction Reliable and secure hardware 24-Hour cu
Technical Library | 2019-07-10 23:36:14.0
Pockets of gas, or voids, trapped in the solder interface between discrete power management devices and circuit assemblies are, unfortunately, excellent insulators, or barriers to thermal conductivity. This resistance to heat flow reduces the electrical efficiency of these devices, reducing battery life and expected functional life time of electronic assemblies. There is also a corresponding increase in current density (as the area for current conduction is reduced) that generates additional heat, further leading to performance degradation.
Technical Library | 2023-09-23 22:25:12.0
Moisture trapped within components and PBs presents a serious problem during the fabrication and assembly process. Too much moisture can lead to board failures when it is turned to steam during the reflow process.
AF04 Cleans condensation traps, solder frames and carriers The kolb AF04 is a three chamber system which enables short cycle times. The system is therefore capable within a short time of parallel process cleaning, rinsing and drying. It cl
VIGON® RC 303 is a water-based cleaning agent specifically developed to remove all types of baked-on flux residues from reflow ovens and wave solder systems. Also, it removes re-condensed fluxes and emissions from condensation traps and heat exchange
SMTnet Express, July 20, 2017, Subscribers: 30,612, Companies: 10,637, Users: 23,528 Reactivity Of No-Clean Flux Residues Trapped Under Bottom Terminated Components Bruno Tolla, Ph.D., Jennifer Allen, Kyle Loomis - Kester Corporation , Mike
