Industry Directory | Manufacturer
The international full service manufacturer of systems, detergents, equipment and process design for the cleaning in electronics production.
New Equipment | Cleaning Equipment
AF03 Small two chamber desktop system for solder frames and condensation traps With AF03 kolb has created a system with a great cost / value ratio that can be called a "clean" alternative for small manufacturers, where the
New Equipment | Cleaning Equipment
Ultrasonic Stencil and Misprint Cleaning Systems Cleaning at the Speed of Sound Ultrasonic - Effective - Safe StencilWasher harnesses the power of sound waves to effectively remove raw solder paste and uncured adhesives from stencils, screens, and
Electronics Forum | Mon Mar 21 08:19:54 EST 2005 | Bob
Sounds like a flaw in your trap. It seams that during the pumping process the trap is ineffective or open, allowing normal sewer gases to bypass the trap and stink up your SMT area. This is similar to what happens when you do not use a drain for a lo
Electronics Forum | Mon Mar 21 21:28:41 EST 2005 | pmd
I agree with dave. Two things prevent oders from drains. The "P" trap and the celing or roof vent. If the system is sealed from the pump on then it should run thru a "P" trap this prevents vapors from comeing back thru the pipe. To make sure suction
Used SMT Equipment | Soldering - Reflow
hh 5 independent controlled heating zones hh Internal cooling zone hh Integrated Ioniser for ESD safe soldering hh DIMAsoft reflow profiler software available hh Flux traps to minimize contamination of the system hh Easy to service one way appro
Used SMT Equipment | Soldering - Reflow
hh 5 independent controlled heating zones hh Internal cooling zone hh Integrated Ioniser for ESD safe soldering hh DIMAsoft reflow profiler software available hh Flux traps to minimize contamination of the system hh Easy to service one way appro
Industry News | 2012-05-11 20:35:45.0
Heller Industries has been awarded a 2012 SMT VISION Award in the category of Soldering Reflow for its 1936 Mark 5 Reflow Oven. The award was presented on April 25, 2012 at the Nepcon China Exhibition.
Industry News | 2012-02-15 19:18:44.0
GPD Global announces that its PCD4H Dispense Pump yields excellent results with phosphor and non-phosphor-filled LED encapsulation as viewed on the color chart by tightly grouped results.
Parts & Supplies | Assembly Accessories
Advantages of KIC START Cheap price. The temperature curve can be drawn quickly and accurately. Immediate and objective temperature curve analysis Easy to use software Manual temperature curve prediction Reliable and secure hardware 24-Hour cu
Technical Library | 2019-07-10 23:36:14.0
Pockets of gas, or voids, trapped in the solder interface between discrete power management devices and circuit assemblies are, unfortunately, excellent insulators, or barriers to thermal conductivity. This resistance to heat flow reduces the electrical efficiency of these devices, reducing battery life and expected functional life time of electronic assemblies. There is also a corresponding increase in current density (as the area for current conduction is reduced) that generates additional heat, further leading to performance degradation.
Technical Library | 2023-09-23 22:25:12.0
Moisture trapped within components and PBs presents a serious problem during the fabrication and assembly process. Too much moisture can lead to board failures when it is turned to steam during the reflow process.
AF04 Cleans condensation traps, solder frames and carriers The kolb AF04 is a three chamber system which enables short cycle times. The system is therefore capable within a short time of parallel process cleaning, rinsing and drying. It cl
VIGON® RC 303 is a water-based cleaning agent specifically developed to remove all types of baked-on flux residues from reflow ovens and wave solder systems. Also, it removes re-condensed fluxes and emissions from condensation traps and heat exchange
SMTnet Express, July 20, 2017, Subscribers: 30,612, Companies: 10,637, Users: 23,528 Reactivity Of No-Clean Flux Residues Trapped Under Bottom Terminated Components Bruno Tolla, Ph.D., Jennifer Allen, Kyle Loomis - Kester Corporation , Mike
ASCEN Technology | https://www.ascen.ltd/face_mask_production_line/689.html
? 7 What traps should be avoided when buying a mask making machine? 1.Income analysis of investment in the mask production line from scratch
Imagineering, Inc. | https://www.pcbnet.com/blog/tips-to-speed-up-the-pcb-assembly-process/
. Edge clearance, acid traps, layout complexity, and solder masks between pads determine a PCB’s manufacturability. While DFM is a common practice in virtually all engineering disciplines, the ways it is implemented can vary
