Overview • two power saving modes: HALT, WAIT • built-in real time hardware on chip debugger • de-multiplexed Address/Data Bus to allow easy memory connection The D6802 is a 8-bit MPU IP Core. The D6802 is synthesisable SOFT Microprocesso
Premium Quality Design ESD Safe NFPA 79 Compliant Numerous Options And Accessories Available! PROMATION’s EWT station may be used for inspection of PCBs or rework. Equipped with an in-line conveyor, in CHECK mode the station stops the
Electronics Forum | Tue Apr 17 13:07:17 EDT 2012 | rodrigo
Well... after much headache I found a bad relay contact in M1CR1E. The good news is somehow the axis are no longer jerking. The bad news is that it still does not work. When I turn it on now it shows this: emergency stop (in red) waiting for reset
Electronics Forum | Thu Apr 12 15:21:12 EDT 2012 | jdengler
Have you tried to do a reset start? When Fuji's act weird the first place to start is a reset start, then re-load the Proper Status and Program. Jerry
Industry News | 2015-06-23 09:50:36.0
Cogiscan announces that Dynamic Source Manufacturing, Inc. (DSM) is installing a major expansion to its Cogiscan Track, Trace and Control (TTC) System. The expanded system will achieve measurable cost savings and improved efficiencies via real-time visibility and control of materials throughout the stockroom, kitting process and entire shop floor.
Industry News | 2017-04-16 17:43:03.0
Scienscope International today announced plans to exhibit in Stand 1H22 at NEPCON China, scheduled to take place April 25-27, 2017 at the Shanghai World EXPO Exhibition & Convention Center. Company representatives will demonstrate the full line up of X-ray component reel counters (AXI 5100c, AXC-800 and AXI 5600c) along with the X-Spection 6000 inspection machine.
Parts & Supplies | SMT Equipment
USE ALTENATIVE PART FUJI RELAY G2R-212S-VNUS DC12V > USE ALTENATIVE PART FUJI RELAY G2R-112S-DC24V TO R2016A > USE ALTENATIVE FUJI RELAY G2R-212S-DC24V TO R2017A > USE ALTENATIVE FUJI RELAY G3R-102SLN DC24V/2A FUJI
Parts & Supplies | SMT Equipment
USE ALTENATIVE PART FUJI RELAY G2R-212S-VNUS DC12V > USE ALTENATIVE PART FUJI RELAY G2R-112S-DC24V TO R2016A > USE ALTENATIVE FUJI RELAY G2R-212S-DC24V TO R2017A > USE ALTENATIVE FUJI RELAY G3R-102SLN DC24V/2A FUJI
Technical Library | 2019-12-12 02:43:44.0
Today we discuss the reason that causes temperature humidity chamber to alarm,In most cases, the equipment alarm is caused by the improper operation in the process of use, which mainly includes following reasons:that are refrigeration system, temperature system and circulating system. First, Refrigeration system 1, refrigeration compressor overpressure alarm. If the refrigerant pressure exceeds the set value, it will stop and alarm at the same time. At this time, the fault must be eliminated and then manually reset. 2, short phase power supply, phase sequence alarm. When the external power supply of the equipment is out of phase or the phase sequence is changed, it will stop and alarm at the same time. 3. The circulating cooling water is short of water to alarm. When the water pressure of the cooling circulating water system is insufficient, it will stop and alarm at the same time, and it must wait for the fault to be eliminated and reset at the same time before it could run normally. 4, refrigeration compressor overheating alarm. When the coil of the compressor is overheated and the power supply of the line is not normal, it will stop and alarm at the same time. Second, Temperature system 1, the overtemperature alarm in the chamber. The sensors in the channel and the sample area are equipped with overtemperature protection devices, and there are also overtemperature protecter on the control panel. When the temperature in the working chamber exceeds the setting value on the controller, it will stop and alarm. 2. sample overtemperature protection. When the temperature in the sample area exceeds the protection temperature set by the controller, it will stop and alarm at the same time. The overtemperature protection of the sample is divided into upper limit protection and lower limit protection, which can be set according to the demand, Third,Circulating system 1. The alarm is caused by the overheating of the circulating fan. When the coil of the fan is over-heated, the alarm will be stopped at the same time. 2. The fan over-current alarm. When the current of the fan exceeds the allowable value, the alarm is stopped at the same time, and the normal operation can only be carried out after the fault maintenance of the overcurrent is completed. This is what we talk about today,if you have more questions,let us know.
SMT FUJI Cp6 Cp7 Cp8 Washer, Lock W1019t Wph0780 FUJI SMT Machine Parts sales@smtpartssupply.com FUJI 13189 LAMP HALOGEN (R1022A) (R1022A) FUJI 100003 Absorber shock KSHA6X15-47W TO A1037W FUJI 100119 ASTRO BELT TIMING 10T5/1500 20.114.01 FU
Career Center | Toronto, Ontario Canada | Production,Quality Control,Technical Support
HIGHLIGHTS OF QUALIFICATIONS • Over 5 years of experience working as a Technical Support person, Onsite Technician in maintenance and operation of business environment to support business such as inventory of equipments and supplies as well as softw
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/how-do-you-download-the-new-v2014-release_topic1326_post5229.html
: Oxfordshire, UK Status: Offline Points: 576 Post Options Post Reply Quote jameshead Report Post Thanks(0) Quote Reply Posted: 30 Apr 2014 at 3:31am I also have problems but get taken to a "password" reset page
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Infrared-Preheat-Module-User-Guide-22140087.pdf
/ stop mode. If errors occur, the user can use reset to clear any errors. Control of the Infrared Preheat Module is activated via the control on the front panel. Special features The Infrared Preheat Module features: • Quartz infrared heaters rapidly