Electronics Forum: 800 (Page 56 of 68)

Re: Depanelization of PCBs

Electronics Forum | Mon Jun 22 21:31:43 EDT 1998 | Dave F

| Dear collegues, | I like to have your comments/ experience with various methods of depanelization like routing, scoring, cutting etc. | Any feed back on the equipment used with company addresses will be highly appreciated. | Please identify if pos

Madder Than Hell

Electronics Forum | Thu Jun 18 13:56:39 EDT 1998 | No Friend Of Alpha

So my salesman says to me that we could return our unneeded Al frames from our MPM printer to Alphametals in CA for credit to be applied toward a future sale. Sonded good. So I boxed up all the damn frames (44) and shipped them off to Goofyland. Now

Re: Madder Than Hell

Electronics Forum | Thu Aug 13 21:58:14 EDT 1998 | Alpha Guy

When things go wrong (see below) it can usually be attributed to a communication problem. This is exactly the issue with this case. A meeting has been held and corrections have been made with no hard feelings. However, another call rather than a

Re: Lemme' re-phrase that

Electronics Forum | Wed Jun 17 08:28:59 EDT 1998 | Dave F

| | Ben: Why not consider some of the training suggestions made by SMTNeter's to Marcos on the tread shown below? Dave F | | Looking for Training in SMT process - Marcos Silva 15:24:13 6/12/98 (7) | Dave- I did happen to look over those posts befor

Re: Solder masks for gold fingers/Try Rubber Shunts

Electronics Forum | Thu Jun 04 20:52:57 EDT 1998 | D.Lange

| | I have gold fingers that I want to mask when running over the wave without pallets. They're on the leading edge of the board. I recall seeing rubber boots that slid onto the fingers to mask them. Pop 'em on before the wave; pop' em off after a

Re: Adhesion of conformal coating to plastic components

Electronics Forum | Wed Jun 03 01:06:13 EDT 1998 | Mike Moninger

| We have experienced poor adhesion of acrylic conformal coating to plastic bodied IC�s. The observed symptoms of this are a blistering or lifting of the coating at the surface of the component, although peel testing has revealed that this is not al

Re: Leader Tape for SMT components/Source, but why?

Electronics Forum | Mon Jun 08 21:20:55 EDT 1998 | Dave F

| | | Is there someone who can tell me where I can buy rolls of leader tape for SMT component tapes. Is there a good way of bonding leader tapes, maybe a special instrument to do the job. Thanks for any help. | | Igmar: The following companies suppl

Re: Residue

Electronics Forum | Tue May 26 16:35:53 EDT 1998 | Ryan Jennens

| | We recently made the switch to no-clean and the wurface mount is turning out beautifully. However, the wave solder process continues to put up a fight; we are getting a white residue on the surface of the PCB. The residue is not localized

Re: DI Water Quality Curve??

Electronics Forum | Thu May 21 22:25:39 EDT 1998 | Mike Konrad

Your experience is typical. The degradation curve of resins resembles the track of a Six-Flags roller coaster. Water quality remains high (10 MW+) for 80% of the resin's life. For a very short time, quality will drop to 7 - 8 MW, then, without noti

Re: turbulent wave restrictions

Electronics Forum | Thu May 07 21:25:56 EDT 1998 | D.Lange

| I am running a board that is .062" thick and has components that over hang the edge of the board by .090". I have bottom side smt components (chip caps and resistors only) and use the turbulent wave to help solder the components. The problem I am


800 searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling Machine with CE

Training online, at your facility, or at one of our worldwide training centers"
Sell Your Used SMT & Test Equipment

Reflow Soldering 101 Training Course
PCB Depanelizers

"Heller Korea"