Electronics Forum: assembleon fcm ii (Page 1 of 7)

Assembleon FCM Base II Cermamic - need info.

Electronics Forum | Mon May 21 18:24:42 EDT 2007 | kz9yyc

Hello, I am looking for any information regarding Assembleon's FCM Base II coordinate system. While some of my problems are due to inexperience and ignorance, I have read every manual, technical bulletin, and online message available to me, and I s

Assembleon FCM Base II Cermamic - need info.

Electronics Forum | Thu May 31 03:12:18 EDT 2007 | vinitverma

Hi John, You can write to me offline at vinit.verma@prosemtechnology.com and write the exact problem that you face after you have generated the action spec using PPS Pro 8.1. What is the problem that you're facing. The coordinate system is taken ca

FCM I - II Software

Electronics Forum | Fri Sep 24 05:39:15 EDT 2004 | vinitverma

Hi, Try Technomatix. That is the one used by Assembleon itself for the FCMs. You can buy the license from them for Assembleon FCMs as well as FUJI machines. The Assembleon PPS designed around Technomatix, gives a very very accurate cycle time calcu

FCM Base II - option PUSHUP - OFF

Electronics Forum | Thu Mar 22 04:03:04 EDT 2012 | vinitverma

The difference between FCM I and FCM II is not only the use of pusher. The vacuum calibration pads are also in different locations - in front in case of FCM I and in the rear for FCM II. Also the pick positions (coordinates) as well as location numbe

FCM Base II - option PUSHUP - OFF

Electronics Forum | Fri Mar 23 02:33:44 EDT 2012 | vinitverma

Their reply is correct. In FCM II and FCM Multiflex there is NO possibility to enable the pusher.

FCM Base II - option PUSHUP - OFF

Electronics Forum | Fri Mar 23 02:18:37 EDT 2012 | smtronic

Thank you for your response. I did this: I changed the whole machine FCM and the FCM II, as you write me everything changed. Programmed new EPROM, etc. FCM machine and it works perfectly as FCM II. Only now I've changed the option to push mechanicall

FCM Base II - option PUSHUP - OFF

Electronics Forum | Mon Mar 05 13:32:05 EST 2012 | SMTronic

I have a machine FCM Base II FCM II feeders are electric. By default, the manufacturer's option pushup is disabled. It can not be incorporated in any way. I need to use it. Can you turn it on in the configuration files? Do you have access to the FCM

Misalignment with Phillips FCM-II

Electronics Forum | Tue Dec 28 19:27:57 EST 1999 | Charley Qin

Hi, Friends Who has the experience on Philips FCM-II mounter? And do you have any suggestion and advice on how to fix 0402 chip misalignment problem? Thanks,

Philips FCM Base II opinions needed

Electronics Forum | Fri Mar 14 15:22:44 EDT 2008 | floydf

My boss is thinking about buying a used Philips FCM Base II. I was wondering if anyone out there has had experience with them, and could offer their opinion. Thanks for any input.

Assembleon FCM Base 1 PPU's HELP!

Electronics Forum | Tue Sep 20 13:37:00 EDT 2005 | jasont

We have x30 PPU's across x3 FCM Base 1's which are not working properly (error is "image too low"??). Please advise on how to repair/replace these (besides Assembleon themselves). Thanks in advance, Jason

  1 2 3 4 5 6 7 Next

assembleon fcm ii searches for Companies, Equipment, Machines, Suppliers & Information

Blackfox IPC Training & Certification

Training online, at your facility, or at one of our worldwide training centers"
pressure curing ovens

High Throughput Reflow Oven
2024 Eptac IPC Certification Training Schedule

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
Electronic Solutions R3

Thermal Transfer Materials.