Electronics Forum | Wed Mar 17 04:26:44 EDT 2010 | mun4o
Hi, we have vitronics delta 6622 in your production.Problem with fluxer starting 3 weeks ago.Fluxer moving, but not spraing????I check flux system , and dont find any problems with machine.Clean the spray nozzle with compressed air , but nothing.may
Electronics Forum | Tue Jun 08 08:40:37 EDT 1999 | Wister
Hi,my master How to iron out such soldering bridge with below conditions: 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB 3.using spraying fluxer and no-clean fl
Electronics Forum | Tue Jun 08 08:38:15 EDT 1999 | Wister
Hi,my master How to iron out such soldering bridge with below conditions: 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB 3.using spraying fluxer and no-clean fl
Electronics Forum | Tue Jun 08 12:49:41 EDT 1999 | Dave F
| Hi,my master | How to iron out such soldering bridge with below conditions: | 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. | 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB | 3.using spraying fluxer and n
Electronics Forum | Tue Jun 08 13:06:53 EDT 1999 | Kevin Hussey
| | Hi,my master | | How to iron out such soldering bridge with below conditions: | | 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. | | 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB | | 3.using spraying fl
Electronics Forum | Tue Jun 08 17:52:53 EDT 1999 | Chrys Shea
| | | Hi,my master | | | How to iron out such soldering bridge with below conditions: | | | 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. | | | 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB | | | 3.using s
Electronics Forum | Fri Sep 14 03:43:16 EDT 2012 | mili
Hello!I have a delta wave with these problems:offtime of lambda wave tracking is too long and when modify offtime setting to a negative value for a fast stop on tracking position of lambda wave, the wave pass on stand-by with a delay of half of leg
Electronics Forum | Fri Sep 04 02:09:03 EDT 2009 | sachu_70
Hi Walter, Do you refer to a sprayfluxer operation? The problem seems to be a parameter setting issue. 1. Ensure the wide angle spray reaches PCB with optimum jet pressure. You could pass a glass plate to understand flux coverage and view Jet pressur
Electronics Forum | Mon May 07 11:09:49 EDT 2007 | davef
4 Fluxer Operation 4.1 Set-Up and Check-Out the Fluxer 4.1.1 Spray Fluxer Set-Up and Check-Out 4.1.1.1 Pass a sample unsoldered board through the machine. 4.1.1.2 Remove the board just after passing through the fluxer and the air knife. 4.1.1.3
Electronics Forum | Thu Sep 06 17:37:05 EDT 2007 | hakerem
Hi Joris - There is an excellent wave solder guide called "Take No Prisoners" that includes instructions for attacking and eliminating solder balls and preventing their recurrence: 1. Increase Dwell Time Solder balls are normally caused by too much f
winsouce.jpg)
.gif)
