Electronics Forum | Tue Feb 16 14:40:54 EST 1999 | john hearty
Has anyone changed out the old 4400 vision processor on a Fuji IP3 and replaced it with a newer 4800 vision processor. What does it take to do this and what does it consist of doing. What do I need to order from Fuji in order to do this.
Electronics Forum | Wed Aug 23 12:04:32 EDT 2006 | fastek
I am going to be scrapping out a 1997 IP-3E soon. It is a complete machine EXCEPT for the 4800 vision card. If there are cards you might need and don't feel like getting hosed by Fuji, let me know. Rick
Electronics Forum | Fri Jun 24 01:01:41 EDT 2005 | FAC
If you are only concerned with the outline and it has 4 corners, VT-10 or 254 will work with backlighting. If the FIP3 machine has a 4400 card installed, frontlighting with high I/O counts could take a while during vision processing. If your machine
Electronics Forum | Thu Feb 14 07:04:19 EST 2008 | daxman
I've never seen that message myself... an idea though.. if your IP3 has a 4400 vision card you'll have seperate LSO cards. The encoders plug directly into them. It could be related to the LSO cards. You could try swapping the LSO cards and see if th
Electronics Forum | Tue Mar 17 16:09:25 EDT 2009 | gregf912
For the IP3 to reliably place BGAs the machine needs the 4800 vision card and type 12 camera. From the problems i see here you must have the 4400 card and a type 8 or 9 camera. It would also seem that a calibration is in order. I have calibrated and
Electronics Forum | Wed Mar 18 07:56:43 EDT 2009 | cyber_wolf
You can calibrate it until you are purple in the face. Job to job and part to part they are just not consistent.They either fail parts or put them on skewed. I have gone back and fourth on this for(10+) years. We have had Fuji look at it and we have
Electronics Forum | Fri Jun 22 11:02:13 EDT 2007 | gregf912
I have a CP642E machine that will not function if auto adjust is enabled in Part Descriptor. Symptom: Auto pick offset causes machine to pick part off center to the point of going to end of part after several picks. This only happens to parts that ha
Electronics Forum | Fri Aug 22 02:10:55 EDT 2014 | mdang
I wonder if anyone can help me with this problem. My FUJI CP65 with 0201 camera is working fine for a while. Now, it starts losing the vision on 0201 camera. The system will run for a while then I don't see the part on the part monitor when the nozzl
Electronics Forum | Tue Mar 17 07:35:37 EDT 2009 | nagesh
We have the IC placer Fuji-IP3 machine.Can this machine be able to place MicroBGA / BGA with good vision system.My card has almost 8 BGA with 4 MicroBGA?Still now i had placed 1 or 2 BGA(Placement by body centering).In this machine the Y- table keeps
Electronics Forum | Tue Dec 06 19:44:10 EST 2011 | comando
Hello every one! I need help with a misaligned theta at plcc44, the machine is a IP3 smd3, firmware 2.99, vision card 4400 and both camera type YD2048N on label but in Proper data is set 2 (I don't know if this is right) we use Fuji flexa, Back Lig
Industrial Sensor Vision International specializes in advanced camera technology of high resolution fast speed cameras for automation, AOI, 2-D/3-D, SPI inspection and wafer inspection.
3 Morse Road 2A
Oxford, CT USA
Phone: +1 203 592 8723
