Electronics Forum | Tue May 16 15:16:26 EDT 2006 | Chunks
Not knowing your brand of Heller, I might suggest disconnecting the first cooling section to verify it's your heater fans. I just had a retro kit done to my Electrovert for a similar thing.
Electronics Forum | Sat Dec 17 16:46:45 EST 2011 | eadthem
Startup current depends on your configuration. ours dose zones 1,2/ 3,4/ 5/ 6,7 last i checked it pulled about 40-55 ish on start up and 25-35 during run. our profile is a slow ramp till 170c then a fast ramp to 285c 280c(last 2 zones). 1707's
Electronics Forum | Tue Oct 18 12:23:04 EDT 2005 | DannyJ
To the Heller question... I have had a few minor bad experiences with Heller. On the 1800 series, redid the movable rail section, which required complete disassembly of the offload end of the oven. A little bit of forethought in design may have ha
Electronics Forum | Fri Jul 20 07:09:29 EDT 2007 | chrispy1963
Sr. Tech, youre absolutely correct that the X-Wagon (pancake) motor is the one which will do final positioning when moving to a programmed position. The X Axis motor in back of the machine is used for rapid traverse of the axis. I was thinking more
Electronics Forum | Thu Mar 02 03:54:30 EST 2017 | rob
Hi Ivam, 1) for the not working motor, can you swap it with another from the cooling zone to see if it is the motor or motor control? 2)You are not getting bleed through from one zone to another are you? Can you list by zone what exact SP you have
Electronics Forum | Mon Sep 27 20:14:37 EDT 2021 | cbeneat
For what it's worth, we have 5 Vitronics ovens. XPM2, 2+, 3I, 3M. Our Oldest is an XPM2-1030 as mentioned. We have never replaced a fan motor. We've been running it for 3 shifts for 16 years. A couple of the gearboxes for the conveyor width have been
Electronics Forum | Fri Sep 24 07:31:13 EDT 2021 | mun4o
Hi all, our company planning to buy a new /third/ smd line.I have choose P&P ,and solder paste printer , but I hesitate about reflow oven.Now we have two smd lines.The first oven is a old ersa hotfow5 - very robust machine. The second reflow oven is
Electronics Forum | Sat Jun 20 19:49:39 EDT 2020 | kylehunter
Hi all. We recently expanded our assembly space and moved our Heller 1500 oven to a new spot. In the old arrangement, we used a Purex filtration unit, keeping the hot air in our space. Recirculating the fumes caused a massive headache in cooling the
Electronics Forum | Mon Oct 05 10:29:38 EDT 2009 | cyber_wolf
I ended up finding that there were broken chords on the X-belt. I replaced it and all is good. Rob, Mydata is right. You can indeed end up spending lots of time and money trying to chase a transducer error. Things I would look at: 1. Lubing the X b
Electronics Forum | Wed Aug 14 13:39:59 EDT 2013 | eadthem
Most of this you have probably covered, but these are what have caused heating issues for us in our 1707 EXL. First, you would probably notice, but check that all blowers are turning by looking at there cooling fans in the top and bottom, Our 170
Reflow ovens for automated SMT PCB assembly, specializing in lead free processing and nitrogen reflow. The best convection reflow ovens on the market.
4 Vreeland Rd.
Florham Park, NJ USA
Phone: 973-377-6800