Electronics Forum | Tue Aug 11 22:30:13 EDT 2020 | kumarb
Jon, please contact Elissa directly to discuss the details. She is a key and repeat supplier to our company for our SMT equipment and supplies. Do note that this is a used motor. Perhaps one of the other contacts above can source a new motor. On th
Electronics Forum | Tue Sep 03 05:39:44 EDT 2013 | bobpan
Yes you can upload modcodes from assembler. This works for all quad c-series machines along with some others. I would NOT overwrite anything. I would save them to a new file so you have the originals. Your original modcodes are good.....your machine
Electronics Forum | Thu Oct 16 04:46:46 EDT 2014 | haiae
I'm looking for a new or used servo motor for my Yamaha YG100R PnP machine with original model: Q2GA04006VXS2C (Sanyo denki ) If anyone can offer it please contact me ASAP. Thanks & best regards,
Electronics Forum | Thu Oct 02 01:59:06 EDT 2008 | edmaya33
Obviously nobody can help you Jack. 1. its the camera for parts recognition ( enhanced CMOS ). 2. positioning system upgraded from ball screw to linear motor/gantry. before CPH=16500 new CPH=18000 using H12S
Electronics Forum | Fri Oct 03 07:49:19 EDT 2008 | grantp
Hi, I just saw the new NXT machines at globaltronics in Singapore, and mostly they are faster. However what was interesting is Fuji shows a prototype of the new XPF machine, but it was called XPF-W which handles really large PCB's and uses the sam
Electronics Forum | Thu May 26 08:52:42 EDT 2011 | davef
Phil Zarrow wrote a useful paper that could help in evaluating paste. Here read it ... Evaluating Solder Paste � Not An Option Contributed by Phil Zarrow of ITM an Independent SMT consulting firm With soldering being the dominant source of assembly
Electronics Forum | Sun Aug 04 19:42:50 EDT 2013 | starlogixs
Thanks for the reply Sarason. The software looks interesting, as we are a small manufacturer. However I do need the original Juki software for a calibration file. The X axis motor has been replaced but the calibration file is missing to teach and ca
Electronics Forum | Thu Oct 04 00:03:28 EDT 2018 | gaintstar
flason smt pick and place machine: http://www.flason-smt.com/product/Hanwha-IC-placer-SM321-High-Speed-SMT-Modular-Chip-Mounter.html http://www.flason-smt.com/product/Hanwha-Pick-and-Place-Machine-DECAN-F2-High-Speed-SMT-Modular-Chip-Mounter.html htt
Electronics Forum | Tue Oct 27 11:20:16 EDT 2009 | smtspecialist
I had the same problem back in March with my MY12, since I have two identical lines i swapped things around until swapping the x-wagon motor (the one for fine movements). When I swapped the x-motor I move the problem from one line to the other gener
Electronics Forum | Wed Oct 26 18:25:13 EDT 2005 | darby
The encoder on the Y axis motor is almost certainly kaput. Debris from the wear of the motor brushes or whatever else can find its way onto the encoder and give an ever increasing false pulse. The axis will start OK but progressively go out of whack
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
3 Road Xintang， Fuhai Street，Fuyong
Shenzhen, 30 China
Phone: 13713862102
.gif)
