Electronics Forum: not centered printing (Page 1 of 19)

Re: printing

Electronics Forum | Mon Jun 29 13:38:20 EDT 1998 | Russ Miculich

| looking for help with fine-pitch printing for what would be the best settings for printing speed, squeegee pressure, seperation speed. | thanks for you time Brian: As Justin says - the issues are many. However, a good start would be to run at 0.75

MyData DPak not placing

Electronics Forum | Mon Jul 29 13:34:28 EDT 2013 | dontfeedphils

Usually the reason it will fail a part like that when you are using mechanical centering is because the part is usually picked so off center because of the body shape. So when the centering jaws close to push the part to center they give up and fail

MyData DPak not placing

Electronics Forum | Fri Jul 26 11:20:33 EDT 2013 | gnus

Hi all, I'm having issues placing 7 pin DPak packages. I'm using mechanical centering with four centering phases (one for each orientation). Tool used is A24S. Machine picks up the part but will reject it when centering the part. I have measured all

MyData DPak not placing

Electronics Forum | Fri Jul 26 12:41:43 EDT 2013 | dontfeedphils

Check the centering force, and change it to High, if it isn't already.

Solder not reflowing properly

Electronics Forum | Thu Aug 28 08:43:56 EDT 2008 | rgduval

You wouldn't think that placement would affect dewetting or solderability....I wouldn't have either, until it was the only thing left in our process, and when we changed it, things got better. I couldn't begin to explain why, either. The only concl

MyData DPak not placing

Electronics Forum | Mon Jul 29 09:43:31 EDT 2013 | cyber_wolf

First figure out which centering phase it is using when the part gets rejected. Then run the machine in step mode and watch whats going on.

MyData DPak not placing

Electronics Forum | Mon Jul 29 13:48:20 EDT 2013 | cyber_wolf

We have placed millions of DPAKS on our Mydatas without issues. Usually the crosshairs need to be just slightly to the right of the dimple when trimming. We do not use high centering force. Please tell us exactly what the error message is.

Solder not reflowing properly

Electronics Forum | Wed Aug 27 14:38:20 EDT 2008 | rgduval

Does your paste provider recommend a TAL? For the leaded and lead-free pastes that we use, the manufacturer recommends 60 seconds above liquidous. I note that your profile shows the TAL as 30 seconds, which may not be sufficient. That said, tho

SOT 23 not reflowing

Electronics Forum | Tue Jan 13 19:41:43 EST 2004 | Tom B

Chris, 1. You may want to check lead finish (plating). 2. Is there shadowing? 3. Is Pik-n-Place providing enough pressure to slighlty push part into paste? 4. Is this a new product? or existing? If existing has suppliers for parts changed? 5. Is

Solder not reflowing properly

Electronics Forum | Thu Aug 28 11:13:53 EDT 2008 | janz

Have you tried to run the same process but with diffrent solder paste manufacturer.? This give you information whether paste is ok. Try also print paste on the bare board and run through reflow oven. Check 2-3 boards. Is it the same places where i

  1 2 3 4 5 6 7 8 9 10 Next

not centered printing searches for Companies, Equipment, Machines, Suppliers & Information

used smt parts china

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
Blackfox IPC Training & Certification

Component Placement 101 Training Course
Win Source Online Electronic parts

Software for SMT placement & AOI - Free Download.
2024 Eptac IPC Certification Training Schedule

Training online, at your facility, or at one of our worldwide training centers"