Electronics Forum | Thu Apr 10 16:02:04 EDT 2008 | brulal1
Hi,we are looking to use Press fit connector on our PCB assemblies. Did anyone out there have any issue with press fit connector? Thank Bruno
Electronics Forum | Mon Jun 27 06:52:07 EDT 2011 | rpatel28364
Hi All We are facing problem with solderability of BGA connector. After Xray we have found open under BGA connector. After removing from PCB it seems some copper pads are still gold. We are not sure why this is happening. We have 5 thou stencil and
Electronics Forum | Thu Jul 08 03:33:33 EDT 1999 | Ron Lahat
Do you have experience with reflow process of a straddle mount connector on a 1.6 mm PCB ? Connector have more than 200 pins What is the process ? Thanks
Electronics Forum | Sat Jul 10 01:45:45 EDT 1999 | Scott
| Do you have experience with reflow process of a straddle mount connector on a 1.6 mm PCB ? | Connector have more than 200 pins | | What is the process ? | | Thanks | Depends on the connector... For connectors that have pre-applied solder such as
Electronics Forum | Wed Oct 22 13:44:41 EDT 2014 | davef
Distributors have access to large number of connector suppliers * http://www.newyorkerelectronics.com/ * http://www.digikey.com/Connectors * http://www.newark.com * http://www.directindustry.com/industrial-manufacturer/card-edge-connector-93613.h
Electronics Forum | Sun Oct 19 06:42:01 EDT 2014 | timbo292832
im designing a circuit that will require the use of a edge connector so it can connect to another circuit. i need to do this so i can get both micro controllers communicating i have done a bit of research and am thinking about using a pcb manufact
Electronics Forum | Thu Jul 08 13:21:18 EDT 1999 | Bob Barr
Ron, We use 100 pin straddle mount connectors on some of our 1.6mm boards (up to eight per board.) They come to us from the vendor with a bead of solder on the somewhat 'J' shaped leads. Our process is as follows: Mount connector to board with hard
Electronics Forum | Mon Oct 20 18:53:39 EDT 2014 | warwolf
pci express x1? https://www.google.co.nz/search?q=pci+express&client=firefox-a&hs=ZJi&rls=org.mozilla:en-GB:official&channel=sb&source=lnms&tbm=isch&sa=X&ei=DZJFVKvRDaXemAXaxoCgDA&ved=0CAgQ_AUoAQ&biw=1173&bih=849#rls=org.mozilla:en-GB:official&chann
Electronics Forum | Fri Sep 17 16:44:56 EDT 2010 | rdubya
If your pads are long enough you shouldn't have a problem, the pins on the connector are curved up(away from pcb)and will plow solder paste to the end of the pad then it will wick back up the pin during reflow. if you have a second stencil for the bo
Electronics Forum | Fri Jun 14 14:30:36 EDT 2002 | davef
Assuming you are talking about solderable surfaces: People specify various materials to protect the solderability of the pads on the board. Gold, actually, Electroless Nickel - Immersion Gold [ENIG], is popular. * Board fabricators like it because
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830