Electronics Forum | Tue Oct 17 12:07:58 EDT 2006 | pms
ya don't need no stinkin pads. just run sum fine gauge insulated jumpah wires from da I.C. legs (da ones with da missin pads) to da traces or where-ever dem traces end up. dat should get er dun !!!!
Electronics Forum | Wed Oct 18 07:51:14 EDT 2006 | davef
Look here: http://www.circuittechctr.com/ As a low cost approach, use copper foil purchased from a stained glass window hobbyist shop. Cut foil pieces to size with a sharp knife. Epoxy the pieces in place of the damaged pads. Tin and then solder th
Electronics Forum | Mon Oct 16 17:46:49 EDT 2006 | Dan
Recently I was given a bad Bios Link from Toshiba which fried my Bios and now my laptop boots to a black screen. I recently unsoldered and removed the existing Bios chip and have ordered anotherfor replacement. Unfortunately while removing, i damag
Electronics Forum | Thu Nov 14 10:18:31 EST 2019 | slthomas
It doesn't look to me like the jumper wire is wetting at all. I would immediately question the solderability - do you know how that jumper wire is finished (plating type)? Also, how experienced are the solderers? It could be that the wire never get
Electronics Forum | Wed Jul 01 13:17:39 EDT 2015 | davef
Cheryl Tulkoff and Randy Schueller do a good job summarizing the thinks on pad cratering here: http://www.smta.org/chapters/files/uppermidwest_padcratering.pdf Potential Mitigations to Pad Cratering * Board Redesign * Solder mask defined vs. non-s
Electronics Forum | Thu Sep 10 15:06:11 EDT 2009 | dyoungquist
My guess is that he is talking about the gold plated pads not fully wetting with solder. We have seen this on some of our ENIG boards with the gold still showing at the far corners of the rectangular pads. Not knowing if this is hand soldering or p
Electronics Forum | Fri Jun 14 14:30:36 EDT 2002 | davef
Assuming you are talking about solderable surfaces: People specify various materials to protect the solderability of the pads on the board. Gold, actually, Electroless Nickel - Immersion Gold [ENIG], is popular. * Board fabricators like it because
Electronics Forum | Fri Dec 04 05:47:57 EST 2015 | rushpcbuk
In PCB design, a BGA (Ball Grid Array) package typically determines the number of layers that a Printed Circuit Board should have. However, the 4-layer board with a BGA package is commonly used than a 2-layer than an 8-layer PCB. On the other hand, t
Electronics Forum | Fri Mar 26 17:12:17 EST 2004 | ben
I have recently encountered a new pcb design with a very high density of components on either side of the pcb. One of the suggested "fixes" is to use the smt pads as vias i.e. the via will be drilled thorough the centre of the smt pad. My concern i
Electronics Forum | Thu Mar 27 14:09:41 EST 2003 | Enrique Chairez
Hi All, I have observed this problem with one PCB supplier, the portion of the PCB area affected was cut and observed in SEM (Scanning Electron Microscope) and submitted to an EDX (Energy Disperse X ray analysis), finding Phosphorus levels higher
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
winsouce.jpg)
