Electronics Forum | Sat Nov 17 10:24:17 EST 2007 | etienne
Hi, I can give my opinion in this topic since I worked with both machines. To say the truth, I would recommend neither machine. First of all, operating software is much quite the same for both machines. The TP9 is true that has a larger footprint ov
Electronics Forum | Mon Nov 12 10:47:53 EST 2007 | dyoungquist
I have never used a topaz but we are currently running a TP9. I can give you some feedback on a TP9 machine. Answer a few questions first and then I can tell you if I think the TP9 is a good fit for you. What size components are you loading? Low o
Electronics Forum | Mon Nov 12 13:35:34 EST 2007 | dyoungquist
MyData TP9s Work well in high mix applications because change over time from 1 job to the next can be done in as little as 15 minutes if you have the right mix of magazines/feeders. Component placement rates vary depending on which component you ar
Electronics Forum | Thu Oct 17 16:09:18 EDT 2002 | Hamish
Has anyone had trouble with SMD machine placing of SC-79 (approx 0402) varicaps (infineon, alpha, philips)? Using the recommended pads from Infineon I am struggling to get the component to place flat on the PCB and the pins to wet properly every time
Electronics Forum | Thu Jul 23 07:33:28 EDT 1998 | The Wretched SMD
200 boards/Hr and oven will reflow ~180 boards/Hr but the P&P machine will only place 700-950 CPH when setup is taken into account. Minimum pitch is normally .020" and we place an Avg. of 491 TSSOPs and 217 BGAs a month. We don't even bother with 04
Electronics Forum | Fri Jul 24 16:02:13 EDT 1998 | Justin Medernach
200 boards/Hr and oven will reflow ~180 boards/Hr but the P&P machine will only place 700-950 CPH | | | when setup is taken into account. Minimum pitch is normally .020" and we place an Avg. of 491 TSSOPs and 217 BGAs a month. | | | We don't even bo
Electronics Forum | Fri Jul 24 12:12:52 EDT 1998 | smd
200 boards/Hr and oven will reflow ~180 boards/Hr but the P&P machine will only place 700-950 CPH | | when setup is taken into account. Minimum pitch is normally .020" and we place an Avg. of 491 TSSOPs and 217 BGAs a month. | | We don't even bother
Electronics Forum | Fri Jul 24 09:50:13 EDT 1998 | Justin Medernach
200 boards/Hr and oven will reflow ~180 boards/Hr but the P&P machine will only place 700-950 CPH | when setup is taken into account. Minimum pitch is normally .020" and we place an Avg. of 491 TSSOPs and 217 BGAs a month. | We don't even bother wit
Electronics Forum | Wed Oct 13 03:38:21 EDT 1999 | Paul Gerits
Hi Morris, I work as a technical consultant, application specialist for Philips EMT (SMT machine suplier). For cost per placement complex calculation can be made. To make a easy one just to hav an idea you can use following. Information needed: Pr
Electronics Forum | Wed Jun 12 11:04:31 EDT 2002 | jwentz
We are evaluating new placement equipment from both Assembleon/Philips and Zevatech/Juki. I would like to get comments, both pros and cons, on anyone's experience with these machines. Thanks in advance! Jon
ORION provides innovative solutions to our customers' EMI/RFI Shielding, Insulating, Screening and Sealing needs in a broad spectrum of manufacturing environments.
Manufacturer / Distributor / Consultant / Service Provider
1 Orion Park Drive
Ayer, MA USA
Phone: 978-772-6000
winsouce.jpg)