Electronics Forum: quad handheld (Page 1 of 2)

Autoprogram

Electronics Forum | Mon Nov 13 12:14:17 EST 2006 | pforister

Jax, I called BP Micro. They don't have offline programming capabilities for the quad machines. They use the handheld and camera system to program the pickups and placements. That was a good try, I forgot BP Micro was using the IIC - IVC machines

QUAD 4C T axis

Electronics Forum | Mon Aug 04 08:02:39 EDT 2008 | leemeyer

Miro, The video has nothing to do with the Quadalign. On a good startup and with no nozzle installed run a "Function 30" and post numbers that you get on the handheld terminal. On a bad startup (nozzle in the down position) press the re button on t

QUAD 4C motor error #5

Electronics Forum | Fri Aug 30 10:35:54 EDT 2013 | nophsem

Data base Utilities --> Download MOD Codes to assembler) and the motor error # 5 appeared instantly in the handheld.

Quad 4C reject PCB stickers

Electronics Forum | Wed Jun 19 07:24:10 EDT 2013 | bobpan

Hello Rollon, There needs to be a contrast between the sticker and board. The manual gives and example of a round red sticker. If you still cant still make this work.....Do the following. Run the machine and after it finds fiducials press stop on the

Quad 4C

Electronics Forum | Wed Jun 05 05:10:10 EDT 2013 | rollon65

Hi all. I already have a pair of Quad 4C Mk2 and purchased a Quad 4C Mk2 CE model secondhand. Some of the machine powers up but not the motor PCBs so the start up sequence stops after the nozzle changer operates with Motor Error #5 on the handheld.

Quad 4C place problem

Electronics Forum | Wed Mar 31 10:08:13 EDT 2010 | leemeyer

First I would only be concerned about the front panel led's if the transport is not clamping. These LED's are most likeley burnt out. If the transport clamps your sensors are working properly. If you are seeing a "Place 1 Z" on the handheld it is ask

Quad IVc Fiducial Alignment

Electronics Forum | Fri Feb 24 09:24:08 EST 2012 | bobpan

1. You should be running the machine from the computer and central contoller. (not the handheld or run button on machine) 2. What is the tep commands in your sequence steps....I think you need to have tep vision as the first step and tep vpass at the

QUAD 4C motor error #5

Electronics Forum | Fri Aug 30 10:50:47 EDT 2013 | bobpan

Clear the memory again and try to input by handheld the modcodes 1 by 1 and see when the problem happens. You can input a number then press home and home. Sounds to me like a number is incorrect but its hard to tell. Are you sure the file that you ar

QUAD 4C motor error #5

Electronics Forum | Wed Aug 28 21:47:22 EDT 2013 | nophsem

HI! We have a QUAD 4C since 8 months . Yesterday the head remained immobile in the position where it put the last component to complete a board and indicates Motor Error # 5 (SRX engine communication time-out) and I don’t know what it means and ho

QUAD 4C motor error #5

Electronics Forum | Fri Aug 30 21:54:14 EDT 2013 | nophsem

Well, the error occurs with Mod Code 56 (dispenser enable). Head # 1 has installed this accessory, but we use it very little and it wasn't this time. I probed setting 0,1,2 and 3. I downloaded Mod Codes from controller to assembler, then the error b

  1 2 Next

quad handheld searches for Companies, Equipment, Machines, Suppliers & Information