PCB Libraries, Inc. | https://www.pcblibraries.com/forum/topic2324&OB=ASC.html
D = 1 - 0.1 +0.2 ? to be 1.05 +/- 0.15 Also How can i generate footprint for package SOT-89 it found in reference but i can't found in tool Tom H Members Profile Send Private Message Find Members Posts Add to Buddy List Admin Group Joined
GPD Global | https://www.gpd-global.com/pdf/pump/NCM5000-Jetting-Pump-Chinese.pdf
• 填满喷嘴底座只需要仅仅0.1毫升 • 可切换不一样的喷嘴 • 喷嘴是由硬质合金或陶瓷制成的,喷嘴内径范围为 0.075毫米至0.2毫米 • 固定着撞针与膜片 Rev Jun 2019 清洗简单,维修容易 拆卸和清洗的步骤非常简单!由于 需求少量的胶水填满喷嘴底座,将 胶水的浪费和损失保持到最低。 要拆卸喷射阀只需拆除两个螺丝 — 这松开喷嘴底座、撞针膜片和 胶罐。由于螺丝可从顶部松开,所 以阀可在清洗过程中保留原位。 清洗程序真简单!把喷嘴底座和撞 针膜片放进超声波清洁器,用合适 干净就行。 点胶
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/efd/products/controllers-and-control-systems/process-generatorspico-controllers
EFD’s PICO dispensing system with your HMI (human machine interface), PLC (programmable logic controller), or personal computer. They produce a high-precision 24 V dispensing signal with signal lengths of 0.2 ms and less
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/topic474&OB=ASC.html
+/- 0.25 else where on the drawing - not too disimilar to the +/- 0.2 mm tolerance suggested by Tom earlier for missing dimensions. I took L1 from the datasheet as
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/transistor-outline-to-dpak-query_topic474_post1410.html
+/- 0.25 else where on the drawing - not too disimilar to the +/- 0.2 mm tolerance suggested by Tom earlier for missing dimensions. I took L1 from the datasheet as
| https://www.eptac.com/wp-content/uploads/2016/08/eptac_08_17_16.pdf
| https://www.eptac.com/wp-content/uploads/2021/11/eptac_08_17_16.pdf
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/sealant-equipment/solutions/battery-cell-bonding-applications
0.2 cc dots in patterns of 2-4, that create enough bond strength to hold the cell in place, uses the least amount of material, but generally requires more application time
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/efd/blog/081017-jet-dispensing-uv-cure-adhesive-to-seal-automotive-sensors
: Fluid Used UV-cure adhesive Application Requirements Shorter dispense cycle time Accurate, consistent deposits 0.8″ long beads 2.8 mg (+/- 0.2 mg) deposit volume Previous Process The manufacturer is using 30cc syringe barrels mounted within an enclosed automated dispensing system to dispense UV-cure adhesive to seal automotive sensors
| https://pcbasupplies.com/jm-20-sn63-pb37-0-3-mm-cored-leaded-solder-wire/
Leaded Flux Cored Solder Wire Product category Flux Cored Solder Wire Flux content(%) 2.2±0.2 Flux type ROL0 Halide content(%) 0.0 Silver chromate paper test No discoloration Solder spreadability