GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Contour-Mapping-Calibration-User-Guide-221MAPDOC-5.pdf
area of the dot. The default value is 12000 pixels. This value may need to be increased when a magnification lens is used. 9. Click on OK and then click on the Reboot warning prompt. STEP 2 - Disable Conveyor Nest Pin Later in this procedure when the
GPD Global | https://www.gpd-global.com/pdf/doc/Contour-Mapping-Calibration-User-Guide-221MAPDOC-5.pdf
area of the dot. The default value is 12000 pixels. This value may need to be increased when a magnification lens is used. 9. Click on OK and then click on the Reboot warning prompt. STEP 2 - Disable Conveyor Nest Pin Later in this procedure when the
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Cyclops-II-Vision-Software-InstallUpdateRestore-Guide-22240108.pdf
application with pre-configured IP address 10.1.0.99 named Cyclops2 connection 10.1.0.99.RDP. User Id: .\GPDUser Password: GPDUser 2- Continue on to Step 2 (pg 7). WARNING: Content made available at the Service level is NOT recommended for use by any- one
GPD Global | https://www.gpd-global.com/pdf/doc/Cyclops-II-Vision-Software-InstallUpdateRestore-Guide-22240108.pdf
application with pre-configured IP address 10.1.0.99 named Cyclops2 connection 10.1.0.99.RDP. User Id: .\GPDUser Password: GPDUser 2- Continue on to Step 2 (pg 7). WARNING: Content made available at the Service level is NOT recommended for use by any- one
KD Electronics Ltd. | http://www.kundasmt.com/?A-Equipment-Accessories/6008.html
=140mm TY 24M 00805142-01 Cable tie w=4.8mm L=186mm TYB-25M 00810041-01 HIGH VOLTAGE LIMIT 00818028-01 HOLDER 3SB19 FOR 3 SWITCH ELEMENTS 3SB1 00818130-01 Service-tool LZ-5 lamp puller 00833078S01 AIR PRESSURE FILTER/VALVE LFR-1/4-S7B 00833136-01 MAGNETIC LATCH SENIOR, WHITE 00845063-01 DIN912-M6 x 40
GPD Global | https://www.gpd-global.com/co_website/pdf/lead-former/CF8-Calculator-Software-Guide-8201622.pdf
limit the range of material printed after selecting one of these options. If the printer is not ready, the software will wait until it is ready; if there is no printer attached, the software ignores the request. 3.1.3 Backup This option allows you to
GPD Global | https://www.gpd-global.com/pdf/lead-former/CF8-Calculator-Software-Guide-8201622.pdf
limit the range of material printed after selecting one of these options. If the printer is not ready, the software will wait until it is ready; if there is no printer attached, the software ignores the request. 3.1.3 Backup This option allows you to
GPD Global | https://www.gpd-global.com/co_website/pdf/dispense/Dispensing-Systems-and-Pumps-Overview.pdf
ultra small, standard, and high volume configurations. • When configured with the smallest auger (062), the pump can dispense solder paste down to 0.005” (125 µm). This newest auger reaches a new limit of dispensing not previously possible. • Standard
GPD Global | https://www.gpd-global.com/pdf/dispense/Dispensing-Systems-and-Pumps-Overview.pdf
ultra small, standard, and high volume configurations. • When configured with the smallest auger (062), the pump can dispense solder paste down to 0.005” (125 µm). This newest auger reaches a new limit of dispensing not previously possible. • Standard
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/FLOware-Messages-Reference-Guide-22100026.pdf
. Mount a board an program or moun Purging... Click DONE to Stop This message appears when purging without a time limit. Purge will continue until a button is clicked