GPD Global | https://www.gpd-global.com/pdf/doc/FLOware-Messages-Reference-Guide-22100026.pdf
. Solution sages Info & Error Messages Reference Guide View Dot Calibration Position or Adjust Manually This message is elf-explanatory. Click CLOSE to c ABORT to termin Jog the camera to the initial point Jog the camera to the farthest x point Jog the camera
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Infrared-Preheat-Module-User-Guide-22140087.pdf
laterally so the conveyor rails are aligned with both upstream/down- stream conveyors so product can transfer smoothly. 3. Level the system: a. Place a precision level on one of the X-axis conveyor rails. b. As necessary, adjust machine leveling feet with an
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Embedded-IR-Heater-User-Guide-22140091.pdf
corner. Figure 12: Camera meter coordinate fields identified in Recipe Manager. Item Name Description 1 Y axis y=0 is the origin point y=60 is the bottom of the image 2 origin point (0,0) is located in upper left corner of camera view. 3 X axis x=0 is the
GPD Global | https://www.gpd-global.com/pdf/doc/Infrared-Preheat-Module-User-Guide-22140087.pdf
so product can transfer smoothly. 3. Level the system: a. Place a precision level on one of the X-axis conveyor rails. b. As necessary, adjust machine leveling feet with an end wrench making any necessary adjustments to overall machine height. c
GPD Global | https://www.gpd-global.com/pdf/doc/Embedded-IR-Heater-User-Guide-22140091.pdf
Error Safety Violation Active 1500 AppError unspecified error This is a general, unde- fined and unexpected fail- ure 1501 OvertempConditionDetected The OptrisCT underboard temperature sen- sor is reporting an over temp condition This is a hardware limit
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Side-Mount-Loader-Unloader-Guide-24000600.pdf
position with four (4) Y axis adjustment plate screws. b. Adjust Loader angle with the four (4) X axis adjustment screws. 4. Repeat the above steps for the Unloader. A B 11/13/17 Side-Mount Loader & Unloader User Guide 3 GPD Global© Installation Adjust
GPD Global | https://www.gpd-global.com/pdf/doc/Side-Mount-Loader-Unloader-Guide-24000600.pdf
position with four (4) Y axis adjustment plate screws. b. Adjust Loader angle with the four (4) X axis adjustment screws. 4. Repeat the above steps for the Unloader. A B 11/13/17 Side-Mount Loader & Unloader User Guide 3 GPD Global© Installation Adjust
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Loader-and-Unloader-User-Guide-24000013M.pdf
24000013, 24000014 Magazine size, minimum 150 mm L x 35 mm D x 117 mm H (5.90” L x 1.37” D x 4.60” H) Magazine size, maximum 300 mm L x 200 mm L x 180 mm H (11.81” L x 7.87” L x 7.08” H) Magazine weight limit*, maximum 8 kg (17.6 lb) *capacity of Z-clamp and
GPD Global | https://www.gpd-global.com/pdf/doc/Loader-and-Unloader-User-Guide-24000013M.pdf
24000013, 24000014 Magazine size, minimum 150 mm L x 35 mm D x 117 mm H (5.90” L x 1.37” D x 4.60” H) Magazine size, maximum 300 mm L x 200 mm L x 180 mm H (11.81” L x 7.87” L x 7.08” H) Magazine weight limit*, maximum 8 kg (17.6 lb) *capacity of Z-clamp and
KD Electronics Ltd. | http://www.kundasmt.com/?A-Equipment-Accessories/6006.html
-Axes) 00321557-03 Gantry Cable (X-Motor) 00321558-03 Gantry Cable (X-Motor / Y-Track) 00321572-02 CABLE:CONTROL UNIT-CONVERSION BOARD 00321577-04 CABLE: LIMIT SWITCH X-AXIS 00321578-04 CABLE: LIMIT SWITCH X-AXIS 00321607-03 BELT GUIDE Y-AXIS 00321633-01
.gif)
