Technical Library | 2020-04-14 15:49:38.0
The number of through-hole components on printed circuit boards (PCB) has declined significantly over the last decade. Miniaturization in electronics has resulted in less THT (through-hole technology) and leads with a finer pitch. For this reason, the soldering of these components has also changed from wave soldering to Point-to-point selective soldering. Soldering these small, fine-pitch components is a challenge when surface mount components (SMD) are positioned very close to THT components on the PCB layout. This study, done in cooperation with a large automotive EMS customer, defines the process windows for through-hole technology for fine-pitch components. It determines what is feasible to solder and defines layout design parameter that make soldering possible with SMD areas and other components on the assembly.
Technical Library | 2013-04-12 08:20:15.0
There is much to read about the shifting sands of electronics manufacturing, including current moves by OEMs to alter their EMS relationships to better mitigate risk and cost, while EMS companies look for additional ways in which to adjust their business models in an attempt to improve their profitability. Electronics outsourcing over time evolved from a means to buffer manufacturing demand fluctuations into a wide scale shift in capabilities, in part in order to deal with vastly shorter product life cycles. Following the global economic crash of 2000, aka “the internet bubble,” more and more EMS providers responded by transferring their manufacturing to low cost labour regions, and in particular China.
Technical Library | 2013-06-13 15:31:24.0
Electromigration (EM) is a mass transportation mechanism driven by electron wind force, thermal gradient, chemical potential and stress gradient. According to Moore’s law, number of transistors on integrated circuits (ICs) doubles approximately every 2 years. Moore’s law holds true since its introduction in 1970s. This insatiable demand for smaller ICs size, larger integration and higher Input/Output (IO) count of microelectronics has made ball grid array (BGA) the most promising connection type in electronic packaging industry. This trend, however, renders EM reliability of solders joints a major bottleneck to hinder further development of electronics industry...
Electronic Packaging Laboratory, State University of New York
Technical Library | 2012-03-15 17:50:28.0
The competition in the EMS sector has considerably intensified over the last few years,. The enormous pressure to reduce production costs, which every service provider today has to face, frequently forces the organization to have a critical look at their
Technical Library | 2019-01-23 21:33:32.0
Automated Optical Inspection (AOI) is advantageous in that it enables defects to be detected early in the manufacturing process, reducing the Cost of Repair as the AOI systems identify the specific components that are failing removing the need for any additional test troubleshooting1-3. Because of this, more Electronic Contract Manufacturing Services (EMS) companies are implementing AOI into their SMT lines to minimize repair costs and maintain good process and product quality, especially for new component types. This project focuses on the testing of component package 03015 which is challenging for AOI.
Technical Library | 2021-09-01 15:31:39.0
The long-standing trend in the electronics industry has been the miniaturization of electronic components. It is projected that this trend will continue as Original Equipment Manufacturers (OEMs) and Electronic Manufacturing Service (EMS) providers strive to reduce "real estate" on printed circuit boards. Typically, the miniaturization of components can be achieved by integration or size reduction. At present, size reduction is considered to be more cost effective and flexible than integration. Passive components, which are used in limiting current, terminating transmission lines and de-coupling switching noise, are the primary focus in size reduction due to their variety of uses.
Technical Library | 2023-11-20 17:42:33.0
Zero-defect strategies and increased demands on the production of assemblies are making quality assurance in electronics production increasingly important. Continous miniaturization of components, ever higher packing densities and the associated hard-to-view assembly areas, as well as the increased use of components such as BGAs, QFNs and QFPs, pose a considerable challenge when it comes to high-precision quality control.
Technical Library | 2016-05-05 15:19:39.0
For many years, manufacturing has sought to increase competitiveness by moving off-shore to countries with lower labour costs. Electronic manufacturing services (EMS) companies provided an essential element to make off-shore transfer happen more quickly, offering further cost reduction opportunities from load balancing. Fierce arguments were put forward to protect the loss of local jobs, although the result was, in almost all cases, inevitable. Today, however, the whole market of PCBbased electronics products has changed significantly. The "pros" of off-shoring are no longer what they once were, and the "cons" are becoming more significant because off-shore manufacturing can no longer satisfy the needs of the market. In this paper, we expose the real costs of off-shore manufacturing, and put labour cost differentials into perspective. We demonstrate how practically, using existing technologies, re-shored manufacturing can yield better business return, either for an OEM, or through EMS providers.
Technical Library | 2014-01-23 16:49:55.0
As reliability requirements increase, especially for defense and aerospace applications, the need to characterize components used in electronic assembly also increases. OEM and EMS companies look to perform characterizations as early as possible in the process to be able to limit quality related issues and improve both assembly yields and ultimate device reliability. In terms of BGA devices, higher stress conditions, RoHS compatible materials and increased package densities tend to cause premature failures in intermetallic layers. Therefore it is necessary to have a quantitative and qualitative test methodology to address these interfaces.
Technical Library | 2015-07-21 13:50:37.0
Achieving an even coat at the right desired thickness is a major challenge when it comes to applying conformal coating to a Printed Circuit Board (PCB). Applying a coating too thin will ultimately render the electronic assembly vulnerable to potential environmental risks therefore defeating the purpose of the coating. Apply the coat too thick, and it could leave the electronic specific components non-functional therefore destroying the electronic assembly entirely. Coating thickness must meet quality specifications. Measurements for coating thickness may be taken while film is dry or wet. Once measurements are recorded, thickness is compared to quality specifications and fluid dispensing automation machinery is calibrated as necessary. There are a handful of methods for measuring conformal coating thickness that are commonly used in the Electronic Manufacturing Services (EMS) and Original Electronic Manufacturer (OEM) industries. A few commonly used methods for checking conformal coating thickness include:
Nordson Electronics Solutions makes reliable electronics an everyday reality. Our ASYMTEK, MARCH, and SELECT brands deliver precision fluid dispensing, conformal coating, plasma treatment and selective soldering equipment.
2747 Loker Ave West
Carlsbad, CA USA
Phone: 18002796835
