Technical Library | 2020-12-02 20:36:54.0
Industry 4.0 is a topic of much discussion within the electronics manufacturing industry. Manufacturers and vendors are trying to come to terms with what that means. In the most simplistic of terms, Industry 4.0 is a trend toward automation and data exchange within the manufacturing process. This basically requires connectivity and communication from machine to machine within the manufacturing line. The challenge is to collect data from each of the systems within the line and make that data available to the rest of the machines. Without test and inspection, there is no Industry 4.0. The whole purpose of test and inspection is to collect actionable data that may be used to reduce defects and maximize efficiency within the manufacturing line. The goal is to minimize scrap and get a really good handle on those process parameters that need to be put in place to manufacture products the right way the first time. For maximum efficiency, three inspection systems are required within the production line. These are solder paste inspection (SPI) post-solder deposition, automated optical inspection (AOI) post-placement, and AOI post-reflow. This requires a substantial investment; however, the combination of all three inspection machines is really the only true way to provide feedback for each stage of the manufacturing process.
Technical Library | 2019-06-17 15:09:43.0
Very often pick and place machines are programmed using CAD data. This data increases the accuracy, precision, and repeatability of its component placement objectives. CAD data makes fine pitch and small component assemblies repeatable, but cannot adjust to a particular board unless it is exactly the same size and shape of the original board used for programming. The process by which printed circuit boards (PCBs) are made only allows some minor changes inboard size and shape, but these small differences are enough for parts to be misplaced. For this reason we use fiducial marks to increase the chances of precise component alignment.
Technical Library | 2019-06-07 14:49:54.0
ACI Technologies was contacted in regards to poor solder joint reliability. The customer submitted an assembly that was exhibiting intermittent opens at multiple locations on a ball grid array (BGA) component. The assembly’s functionality did not survive international shipping, essentially shock and vibration failures, immediately making the quality of the solder joints suspect. The customer was asked about the contract manufacturer and the reflow oven profile as well as the solder paste and surface finish used. The ACI engineering staff evaluated the contract manufacturer’s technique and determined that they were competent in the methods they used for placing thermocouples in the proper locations and developing the reflow oven profile. The surface finish was unusual, but not unheard of, in that it was hard gold over hard nickel, rather than electroless nickel immersion gold (ENIG). The customer was able to supply boundary scan testing data which showed a diagonal row of troublesome BGA pins.
Technical Library | 2023-11-14 02:36:41.0
Understanding In-Circuit Testing (ICT) with PCBA ICT Testing Machine In-Circuit Testing, commonly known as ICT, stands as a sophisticated and precise method within electronics manufacturing. It serves to evaluate the functionality and integrity of individual electronic components on a Printed Circuit Board (PCB). The process employs specialized equipment called ICT Testers, meticulously designed to pinpoint defects, shorts, opens, and other potential issues within the PCB assembly. The Crucial Role of PCBA ICT Testing Machine 1. Quality Assurance ICT is pivotal in ensuring the overall quality and reliability of electronic products. Early identification and rectification of defects in the production process help manufacturers avoid costly recalls, rework, and post-production issues. 2. Cost-Efficiency ICT significantly reduces manufacturing costs by identifying defects at an early stage. This results in fewer defective units reaching the end of the production line, minimizing waste and rework. 3. Faster Time-to-Market Manufacturers can expedite the production process with ICT by swiftly identifying and resolving issues. This leads to faster product launches, providing a competitive edge in the market. Unveiling the Functions of PCBA ICT Testing Machine The ICT Tester, the core of the In-Circuit Testing process, conducts a battery of tests on each PCB, including: 1. Continuity Testing Checks for open circuits, ensuring all connections are properly established. 2. Component Verification Verifies the presence and orientation of components, ensuring alignment with the PCB design. 3. Functional Testing Some ICT Testers execute functional tests, assessing electronic components' performance as per specifications. 4. Short Testing Identifies unintended connections or shorts between different components on the PCB. 5. Insulation Testing Checks for isolation between different circuits, ensuring no undesired connections or paths. 6. Programming and Configuration In some cases, ICT Testers are used to program and configure specific components on the PCB. Advantages of PCBA ICT Testing Machine 1. High Precision ICT offers unparalleled accuracy in defect detection, making it crucial in modern electronics manufacturing. 2. Speed and Efficiency ICT Testers enable rapid testing, allowing manufacturers to assess a large number of PCBs in a short time. 3. Customization ICT Tests can be tailored to suit specific PCB requirements, ensuring thorough evaluation of every design aspect. 4. Data Collection ICT Testers gather valuable data for process optimization and quality control. In-Circuit Testing (ICT) is fundamental in electronics manufacturing, safeguarding product quality, reducing costs, and accelerating time-to-market. The ICT Tester, with its precision and efficiency, positions manufacturers at the forefront of the highly competitive electronics industry. Embracing ICT is not just a choice; it's a necessity for manufacturers striving for excellence in their products. I.C.T is a leading manufacturer of full SMT line machines in the electronic manufacturing industry. Discover how we can enhance product quality, boost performance, and reduce costs. Contact us at info@smt11.com for reliable global supply, unparalleled efficiency, and superior technical service.
Technical Library | 2020-12-16 18:50:42.0
System operating speeds continue to increase as a function of the consumer demand for such technologies as faster Internet connectivity, video on demand, and mobile communications technology. As a result, new high performance PCB substrates have emerged to address signal integrity issues at higher operating frequencies. These are commonly called low Dk and/or low loss (Df) materials. The published "typical" values found on a product data sheet provide limited information, usually a single construction and resin content, and are derived from a wide range of test methods and test sample configurations. A printed circuit board designer or front end application engineer must be aware that making a design decision based on the limited information found on a product data sheet can lead to errors which can delay a product launch or increase the assembled PCB cost. The purpose of this paper is to highlight critical selection factors that go beyond a typical product data sheet and explain how these factors must be considered when selecting materials for high speed applications
Technical Library | 2016-09-12 10:16:04.0
It is hard to open an Industry newsletter or visit an equipment manufacturer’s website without coming across a mention of the Internet of Things (IoT), Industry 4.0, SMART Manufacturing or ‘big data’. The accessibility to obtain data will only increase and this information and its real-time processing will become one of the most important resources for companies in the future. Production machinery will no longer simply processes the product, but the product will communicate with the machinery to tell it exactly what to do. Industry 4.0 has the vision to connects embedded system technologies and SMART production processes to drastically transform industry and production giving way to the SMART factory development. Future development in oven technology will allow machines to be controlled more intelligently and remotely resulting in the lowest cost model for manufacturing flow.
Technical Library | 2015-09-10 15:06:17.0
A new non-halogen flame retardant has been developed and is useful for a variety of high performance applications. This non-reactive phosphorus-based material satisfies fire safety needs for a broad range of resins including epoxy, polyolefin, and polyamide. The combination of excellent flame retardant efficiency, high thermal stability and exceptional electrical properties is unique to this organophosphorus flame retardant and makes it a breakthrough technology for high speed, high frequency use in fast growing wireless and wired infrastructures. Resin performance data, including formulations with synergists, are presented in this paper.
Technical Library | 2017-09-28 16:36:33.0
These nano-coatings also refine the solder paste brick shape giving improved print definition. These two benefits combine to help the solder paste printing process produce an adequate amount of solder paste in the correct position on the circuit board pads. Today, stencil aperture area ratios from 0.66 down to 0.40 are commonly used and make paste printing a challenge. This paper presents data on small area ratio printing for component designs including 01005 Imperial (0402 metric) and smaller 03015 metric and 0201 metric chip components and 0.3 mm and 0.4 mm pitch micro BGAs.
Technical Library | 2023-06-12 18:33:29.0
This paper presents a real-time predictive approach to improve solder paste stencil printing cycle decision making process in surface mount assembly lines. Stencil cleaning is a critical process that influences the quality and efficiency of printing circuit board. Stencil cleaning operation depends on various process variables, such as printing speed, printing pressure, and aperture shape. The objective of this research is to help efficiently decide stencil printing cleaning cycle by applying data-driven predictive methods. To predict the printed circuit board quality level, a recurrent neural network (RNN) is applied to obtain the printing performance for the different cleaning aging. In the prediction model, not only the previous printing performance statuses are included, but also the printing settings are used to enhance the RNN learning. The model is tested using data collected from an actual solder paste stencil printing line. Based on the predicted printing performance level, the model can help automatically identify the possible cleaning cycle in practice. The results indicate that the proposed model architecture can predictively provide accurate solder paste printing process information to decision makers and increase the quality of the stencil printing process.
Technical Library | 2016-01-21 16:52:27.0
Solder paste has long been viewed as "black magic". This "black magic" can easily be dispelled through a solder paste evaluation. Unfortunately, solder paste evaluation can be a challenge for electronic assemblers. Interrupting the production schedule to perform an evaluation is usually the first hurdle. Choosing the solder paste properties to test is simple, but testing for these properties can be difficult. Special equipment or materials may be required depending upon the tests that are chosen. Once the testing is complete, how does one make the decision to choose a solder paste? Is the decision based on gut feel or hard data?This paper presents a process for evaluating solder pastes using a variety of methods. These methods are quick to run and are challenging, revealing the strengths and weaknesses of solder pastes. Methods detailed in this paper include: print volume, stencil life, response to pause, open time, tack force over time, wetting, solder balling, graping, voiding, accelerated aging, and others.