Technical Library: searches (Page 1 of 1)

Internet Marketing Article 01-24-2013

Technical Library | 2013-01-24 20:15:46.0

Being found in the search engines for a wide variety of terms directly related to my business would be my 1st priority...

SMTnet

Mass Analysis Of The Components Separated From Printed Circuit Boards.

Technical Library | 2010-09-23 20:23:37.0

Methods of effective and ecological recycling of printed circuit boards (PCBs) are searched all over the world at this time. The material composition and temperature properties of PCB are necessary to be known for an optimal recycling technology. For thi

Acta Montanistica Slovaca

Progressive Failure Analysis of Laminates with Embedded Wrinkle Defects Based on an Elastoplastic Damage Model

Technical Library | 2021-03-04 15:16:27.0

Out-of-plane wrinkling has a significant influence on the mechanical performance of composite laminates. Numerical simulations were conducted to investigate the progressive failure behavior of fiber-reinforced composite laminates with out-of-plane wrinkle defects subjected to axial compression. To describe the material degradation, a three-dimensional elastoplastic damage model with four damage modes (i.e., fiber tensile failure, matrix failure, fiber kinking/splitting, and delamination) was developed based on the LaRC05 criterion. To improve the computational efficiency in searching for the fracture angle in the matrix failure analysis, a high-efficiency and robust modified algorithm that combines the golden section search method with an inverse interpolation based on an existing study is proposed.

Jinan University

Sample Preparation For Mitigating Tin Whiskers In Alternative Lead-Free Alloys

Technical Library | 2016-02-18 18:55:09.0

As lead-free alloys shift into high reliability electronics, the issue of tin whisker growth remains a primary concern among those in the industry. Current research shows that there is no perfect alloy for all cases of electronic usage. Industry leaders and researchers continue to study and search for a lead free alloy that is able to withstand harsh environments while maintaining high reliability.

AIM Solder

A Novel Local Search Integer-Programming-Based Heuristic for PCB Assembly on Collect-and-Place Machines

Technical Library | 2011-11-03 18:04:07.0

This paper presents the development of a novel vehicle-routing-based algorithm for optimizing component pick-up and placement on a collect-and-place type machine in printed circuit board manufacturing. We present a two-phase heuristic that produces soluti

Mechanical Science and Engineering at UIUC

Facility Fluids Metrics and Test Methods

Technical Library | 1999-08-05 10:52:56.0

This technology transfer was prepared by the Research Triangle Institute (RTI) as part of SEMATECH's Facility Fluids Project (S100). It is a compilation of information on existing facility fluids metric and test methods. Information on standard methods was gathered from SEMATECH and SEMI. Other information was obtained from a literature search of journals and conference proceedings. The published information primarily is concerned with the test equipment used and what levels of detection and purity were found. Many of the articles discussed the use of new equipment, either commercial or experimental. Extensive annotated bibliographies are append to the report.

SEMATECH

Criminal Prosecution - Who can be held liable for the sale of counterfeit parts?

Technical Library | 2011-09-26 13:53:30.0

On September 14, 2010, the late Shannon Wren, owner of VisionTech Components ("VisionTech"), and Stephanie McCloskey, VisionTech's Administrative Manager, were arrested during the execution of search and seizure warrants issued against the pair by the United States government after evidence connected them to the sale of counterfeit parts to the U.S. Navy, defense contractors and others. A ten-count indictment charged McCloskey with conspiracy, aiding and abetting in violation of Title 18 United States Code, Sections 371 and 2; trafficking in counterfeit goods, in violation of Title 18 United States Code, Section 2320; and mail fraud, in violation of Title 18 United States Code, Section 1341. McCloskey pled guilty to conspiracy and aiding and abetting for her role in the scheme.

ERAI Inc.

Exceptional Optoelectronic Properties of Hydrogenated Bilayer Silicene

Technical Library | 2015-03-19 20:33:34.0

Silicon is arguably the best electronic material, but it is not a good optoelectronic material. By employing first-principles calculations and the cluster-expansion approach, we discover that hydrogenated bilayer silicene (BS) shows promising potential as a new kind of optoelectronic material. Most significantly, hydrogenation converts the intrinsic BS, a strongly indirect semiconductor, into a direct-gap semiconductor with a widely tunable band gap. At low hydrogen concentrations, four ground states of single- and double sided hydrogenated BS are characterized by dipole-allowed direct (or quasidirect) band gaps in the desirable range from 1 to 1.5 eV, suitable for solar applications. At high hydrogen concentrations, three well-ordered double-sided hydrogenated BS structures exhibit direct (or quasidirect) band gaps in the color range of red, green, and blue, affording white light-emitting diodes. Our findings open opportunities to search for new silicon-based light-absorption and light-emitting materials for earth-abundant, high efficiency, optoelectronic applications.Originally published by the American Physical Society

Oak Ridge National Laboratory

Essentials about Printed Circuit Board Assembly

Technical Library | 2019-10-18 10:37:25.0

It usually does not make any logic to invest in costly fabrication equipment in case you just desire to spin some prototypes and rather outsource your Printed Circuit Board assembly as well as prototype fabrication to a trustworthy vendor. I would provide a few tips as to what to consider when seeking a contract manufacturer. The two most common procedures associated with Printed Circuit Board Assembly are through-hole technology and surface mount technology. Talking about the difference between through-hole technology and surface mount technology. Through-hole elements have metal leads, & these metal leads are supplied through-plated holes inside the circuit board. On the other hand, SMT elements might or might not have leads, nevertheless most significantly, they are developed to be soldered onto the surface of the circuit boards straight on the same side as the element body. A lot of contract manufacturers would provide a quick quote mechanism over their site for the fabrication of circuit boards as well as assembly of prototypes. This would bank your time when comparing various vendors. Ensure that the quote system facilitates you to fill your details, for instance, board material, thickness, copper thickness, milling, etc. in order that you can avail of a precise quote devoid of any surprises afterward. And this is quite necessary. Typically the cost per board would decline as quality upgrades. This is owing to the fairly high setup price of circuit board fabrication over and above component assembly. A few vendors would employ a system where they unite boards from various consumers. This manner the setup price would be circulated among numerous clients. When you fabricate an item, you clearly don’t desire to have to fabricate a big quantity of boards straight away whilst you improve your design. One restriction with small quantity prototypes though is that the option of materials & material thicknesses would be constrained. In case you are employing a particular material then opportunities are there will not be any other clients employing the same material. Additionally, lead time plays a major role in indecisive prices. A longer lead time facilitates the fabricator more liberty in slotting your fabrication. This is basically reflected in cheaper prices that would view in the quote section. Clearly, if you are in a hurry and desire to be moved to the summit of the pile you would require splurging more dollars. Ensure that your contract fabricator would support the file sort for producing which you offer. The most general format for printed circuit board fabrication is the Gerber format nonetheless a few vendors would moreover embrace board files from general printed circuit board software products. A few suppliers also provide in house printed circuit design. Even in case, you create your board yourself, choosing a vendor with design services might prove resourceful in case there is an issue with your files. In this scenario, your vendor could make swift changes that would neglect pricey delays. If you are looking for an Electronic Manufacturing Services (EMS Assembly) provider, then the web is the best to search.

Optima Technology Associates, Inc.

  1  

searches searches for Companies, Equipment, Machines, Suppliers & Information