Technical Library | 2009-10-29 11:45:52.0
The globalization of markets results in stronger competition with clearly noticeably cost pressure. For companies producing electronic equipment it is therefore of existential importance to reduce production costs whilst maintaining a consistently high quality level of the manufactured products. Manual repair soldering that is expensive, time-consuming and cost intensive is already unacceptable due to the required quality and the reproducibility of the whole manufacturing process.
Technical Library | 2021-08-11 00:57:57.0
This paper shows the Design and Finite Element analysis of vacuum chamber of potting machine designed for electronic ignition coil applications. There are two types of potting methods 1) With Vacuum 2) Without Vacuum.
Technical Library | 2021-12-31 06:09:47.0
The packaging method of surface mount components has become an important part of the SMT system. It directly affects the efficiency of assembly production and must be optimized in combination with the type and number of feeders of the SMT machine. There are four main types of packaging for surface mount components, Tape, tube, tray and bulk.
Technical Library | 2015-05-14 15:45:45.0
The Printed Circuit Board industry has seen a steady reduction in pitch from 1.0mm to 0.4mm; a segment of the industry is even using or considering a 0.25mm pitch. This has increased the use of stacked microvias in these designs. The process of stacking microvias has been practiced for several years in handheld devices; however, the devices generally do not operate in harsh conditions. Type 1 and Type 2 microvias have been tested over the years and have been found to be very reliable. We do not have enough test data for 3 and 4 stack microvias when placed on and off buried via. The main objective of this study was to understand the reliability of 3 and 4 stack microvias placed on and off a buried via.
Technical Library | 2024-02-05 17:51:01.0
Objective: Drying = reducing the humidity in PCB before soldering Preventing delamination caused by thermal stress after moisture absorption Methods: Drying in convection and/ or vacuum oven Parameters subject to material type, soldering surface, layer count, time to soldering, layout (copper-plated areas)
Technical Library | 2020-10-27 02:02:17.0
Solder powder size is a popular topic in the electronics industry due to the continuing trend of miniaturization of electronics. The question commonly asked is "when should we switch from Type 3 to a smaller solder powder?" Solder powder size is usually chosen based on the printing requirements for the solder paste. It is common practice to use IPC Type 4 or 5 solder powders for stencil designs that include area ratios below the recommended IPC limit of 0.66. The effects of solder powder size on printability of solder paste have been well documented. The size of the solder powder affects the performance of the solder paste in other ways. Shelf life, stencil life, reflow performance, voiding behavior, and reactivity / stability are all affected by solder powder size. Testing was conducted to measure each of these solder paste performance attributes for IPC Type 3, Type 4, Type 5 and Type 6 SAC305 solder powders in both water soluble and no clean solder pastes. The performance data for each size of solder powder in each solder paste flux was quantified and summarized. Guidance for choosing the optimal size of solder powder is given based on the results of this study.
Technical Library | 2009-10-22 02:38:13.0
An electronic product's reliability has the potential to make or break its manufacturer and can be life-threatening in many safety critical applications. Conformal coatings have long been used to protect electronic assemblies from their operating environment but can vary hugely in their protective performance. It is the objective of this article to explain in detail why it is important to qualify coating products to the relevant standards and how different coating types affect performance.
Technical Library | 2021-12-17 01:30:28.0
Diffusion silicon pressure transmitter is applied in a wide variety of industries, such as petroleum, chemical industry, steel, power, light industry and environmental protection industry. It can complete the work of measurement and control of the gauge pressure, negative pressure or absolute pressure of various fluid pressure. Most importantly, this type of transmitter can be used in corrosive medium and harsh or dangerous environment. In the process of using the transmitter, there may be some faults or problems.
Technical Library | 2013-07-11 15:22:40.0
This research paper will focus on the effect of various parameters that are used to reball a BGA and their effect on the overall shear strength. Factors that will be looked at include the type of BGA (SAC305 or 63Sn/37Pb), the alloy used to reball (SAC405 or 63Sn/37Pb), the type of flux used (Water Soluble or No Clean), and the environment in which reballing takes place (Nitrogen or Ambient).
Technical Library | 2020-01-22 22:52:02.0
Flip chip assembly techniques bring a wide range of benefits: Reduced parasitic interconnection between the semiconductor die and package. Provides a high final assembly integrity density. Minimize the interconnection length, providing better electrical performances, especially for high speed signals. Reduce the device size and weight,…, etc. But there is no dedicated inspection requirements nor DPA standard which address all the necessary aspects associated to this construction type or only cover partially the topics to be inspected.
