Electronics Forum | Sat Dec 12 04:21:13 EST 2009 | nkohler
Hello, We use SJ50 serie AOIs. I made a program which watches the .dat file and if an algorithm changes then my program makes a log file from the parameters of the modification. I know some numbers are which parameters, but I don't know all. I write
Electronics Forum | Wed Jun 25 11:30:04 EDT 2008 | samir
or... like this? 0 0 0 0 0 0 0 0 0 0 0 0 FLOW DIRECTION --->
Electronics Forum | Mon Feb 04 12:28:28 EST 2008 | jseagle
1.0mm (0.039") 1.75X >0.5 to 1.0mm (0.02 to 0.039") 4X 0.25 to 0.5mm (0.00984 to 0.02") 10X
Electronics Forum | Tue Feb 04 22:28:16 EST 2003 | davef
You could reduce the paste by about 70%. Solder balling and tombstoning will be the issues to fight. The drivers to these don't change with the component size. Use the fine SMTnet Archives for background. Aperture Size and Thickness of Solder Pas
Electronics Forum | Mon Sep 14 09:25:49 EDT 1998 | Dave F
0.050" -> 50 mil -> 50 pitch | 0.80 mm -> 0.032" -> 32 mil -> 32 pitch | 0.64 mm -> 0.025" -> 25 mil -> 25 pitch | 0.50 mm -> 0.020" -> 20 mil -> 20 pitch | 0.40 mm -> 0.016" -> 16 mil -> 16 pitch | 0.20 mm -> 0.012" -> 12 mil -> 12 pitch | Dave F Y
Electronics Forum | Wed Apr 10 22:23:48 EDT 2002 | davef
IPC-6012A, 3.4.1 has words to the effect of: Hole size tolerance and hole pattern accuracy shall be as specified in the procurement documentation. Our fab says: Standard Drill Sizes Drill Number ||Hole Size ||Finished Hole Size 70 ||0.028" ||0.02
Electronics Forum | Wed Apr 10 22:24:30 EDT 2002 | davef
IPC-6012A, 3.4.1 has words to the effect of: Hole size tolerance and hole pattern accuracy shall be as specified in the procurement documentation. Our fab says: Standard Drill Sizes Drill Number ||Hole Size ||Finished Hole Size 70 ||0.028" ||0.02
Electronics Forum | Fri Sep 11 16:52:00 EDT 1998 | Dave F
0.050" -> 50 mil -> 50 pitch 0.80 mm -> 0.032" -> 32 mil -> 32 pitch 0.64 mm -> 0.025" -> 25 mil -> 25 pitch 0.50 mm -> 0.020" -> 20 mil -> 20 pitch 0.40 mm -> 0.016" -> 16 mil -> 16 pitch 0.20 mm -> 0.012" -> 12 mil -> 12 pitch Dave F
Electronics Forum | Mon Feb 22 12:04:15 EST 1999 | Dave F
| Please could you suggest a recommended aperture sizes for | printing of smd adhesives. Any recommendations on stencil thickness as well as stencil finish will be appreciated. | Mark: About the only rule of printing adhesives is: Keep it off the
Electronics Forum | Mon Apr 09 14:53:19 EDT 2007 | flipit
Hi, We were running with few defects with lead solder paste. The lead solder paste with stencil 0.010" X 0.020" and 0.004" thick stencil produced near defect free PCB assys. 0.010" X 0.020" (0.004" thick) lead = defect free 0.010" X 0.020" (0.005"