Electronics Forum: .bad (Page 1 of 248)

Servo Alarm on FUJI IP-2 (MTU unit)

Electronics Forum | Thu Sep 15 16:02:20 EDT 2005 | jdengler

Over Current means the motor is drawling too much current. Check for a jam on that axis, bad wire, bad motor, bad servo amp (yes the amp can go bad and make it appear that the motor is drawling too much current). Jerry

Thermal Relief Pad causes bad solder

Electronics Forum | Thu Aug 18 00:19:09 EDT 2016 | souldierann

Hi there. would it be possible that thermal relief pads for relay bring bad solder?

what is the cause of green decay on the soldered wires

Electronics Forum | Thu Dec 08 18:59:04 EST 2005 | KEN

Is this a wire dip tinning process? If yes, then your flux is probably trapped under the insulator, causing corrosion. BAD BAD BAD (hopefully you don't make wire harnesses for air planes or passenger trains). More info please.

Mydata A12 tool tip damage

Electronics Forum | Wed Jul 18 07:48:12 EDT 2007 | cyber_wolf

Bad small X motor most likely. Other possibilities: Bad cables Bad Card

unknown nozzle st 17

Electronics Forum | Wed Nov 20 10:21:09 EST 2013 | cyber_wolf

Station 17 and 19 errors are almost always caused by dirty clutches or bad sensor dogs. My guess would be bad sensor dogs in this case if it only does it on certain jobs. The reason it happens on those jobs is because there are nozzles being indexed

Error on FUJI IP-2

Electronics Forum | Fri May 06 16:19:40 EDT 2005 | jdengler

Does the problem happen at start-up? Does the servo amp have an error? If yes to both, could be a bad cable, or a badly tuned servo amp. If after running and the amp has an error it could still be the cable but also brings in things like a bad motor

Omniflow reflow blowers going bad ?

Electronics Forum | Wed Sep 12 13:11:50 EDT 2007 | nitro

Usually the bearings lock up. I keep one spare blower on hand and change it out when I have one go bad, then take the bad one apart and change the bearings. The bearings are about $4.00 per set and are pretty common. Not too hard to find. I am using

Jot Automation inspection conveyor failure

Electronics Forum | Tue Oct 21 08:06:15 EDT 2008 | maheshbs

I have problem in Jot Automation inspection conveyor. The Problem is that the Good board has to go in down side conveyor & Bad board has to go in upside for rejection or rework. It is unable to separate the good & bad boards. Kindly refer the attachm

poor print definition

Electronics Forum | Tue Feb 21 09:19:50 EST 2006 | Chunks

Hi Mark, Not to be condescending, but is your 265 camera in focus? I've seen one instance of this. If it�s not the camera, and you are sure all your other parameters are good, , then poor definition can be from bad snap-off or bad gasketing. Snap

REG: BGA REWORK STATION ( BEST EQUIPMENT)

Electronics Forum | Wed Apr 11 15:56:54 EDT 2007 | egrice

CECIL, I am sorry to hear that you had a bad experience with ERSA. However, one bad experience does not mean that ERSA is a bad company. On the smaller BGA Rework systems, sometimes the sales reps do the installations. Was this the case? If so,

  1 2 3 4 5 6 7 8 9 10 Next

.bad searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling with CE

Smt Feeder repair service centers in Europe, North, South America
fluid dispenser

Stencil Printing 101 Training Course
PCB Handling Machine with CE

Training online, at your facility, or at one of our worldwide training centers"
2024 Eptac IPC Certification Training Schedule

High Throughput Reflow Oven