Electronics Forum | Fri Apr 06 19:06:38 EDT 2007 | davef
There is no standard for what you're trying to accomplish. We recall a similar thread on SMTnet. In it, a poster suggested: "Call them: 1206T.5, 1206T1.0, SOIC16, RESNET16, SOIC16T5.0, ALCAP4, ALCAP5 etc., where: T means thickness but for the ALCAP
Electronics Forum | Wed Jun 27 11:59:55 EDT 2007 | samir
*Preheat zone *Maximum slope is a time/temperature relationship that measures how fast the temperature on the printed circuit board changes. The ramp�up rate is usually somewhere between 1.0 �C and 3.0 �C per second, often falling between 2.0 �C and
Electronics Forum | Fri Feb 01 08:40:12 EST 2008 | jdengler
Hi AJ, Change ALL 12 of the 1.0mm to 0.7mm. The CP 4 can only set nozzle size for S M and L not some of the 12 but all 12. 0402 usually come in 8 x 2 mm tape so you need 8 x 2 feeders or you will waste 1 component for every component you use. T
Electronics Forum | Wed Nov 12 14:46:58 EST 2008 | hutch770
Greetings all, I'm pretty new to the SMT world, having been a class 10 fab monkey in my previous life. What I'm looking for is recommendations for pneumatic lead cutters. I need them to flush-cut as close as possible to the via without destroying
Electronics Forum | Wed Aug 05 11:08:36 EDT 2009 | spitkis2
Hi, This may be a bit off the subject but thought I'd ask just in case. I am looking to identify a process / equipment for attaching solder balls to flip chips. Solder balls are 75 microns in diameter. With BGA's there are reballing kits that use
Electronics Forum | Wed Dec 02 20:11:37 EST 2009 | prodivegsr
Hi Lou, we are using a fluid dispensing machine. our current requirement is around 50um. From the Datasheet,the thinner 73 has a higher evaporation rate of 1.0 comapring with thinner 521 at 0.6... does the higher evaporation rate eliminate the bu
Electronics Forum | Fri Mar 26 23:07:07 EDT 2010 | dekhead
Just a guess: Are you printing your fiducials on the fiducial side of the board? Fidicial Side is for Vision Calibration, Bare Copper Side is for Offset Calibration (Step 5 of procedure says "copper side uppermost"). After printing 25 fiducials o
Electronics Forum | Tue Jul 13 13:37:23 EDT 2010 | pjc
That's cold compared with this specification from a leading oven mfr.: Flow Rate - 1.0 - 3.0 US gal/min (3.79 - 11.4 l/ min) • Inlet size and pressure - 0.5 in. male NPT; 310 - 483 kPA (45 - 70 psi) • Pressure drop - 200 kPa @ 11.4 l/min (30 psi @ 3
Electronics Forum | Fri Aug 02 05:35:17 EDT 2013 | peteralmendrala
Sir thank you very much. Sir is it possible for you to give me also a copy of the video driver software 1007545 rev a.? and spm series software boot disk ver 1.0 By the way does the software you provided me runs in windows 95? because ours in running
Electronics Forum | Thu Oct 26 12:14:34 EDT 2017 | lefwan
Our DEK 265 machine is showing this error message during starting…than it keeps re-starting in endless loops: Diskette drive failure on drive A Fixed Disk Controller Failure Fast ready check - Version 1.0 Copyright Arcom Control Systems Ltd. CMOS
.gif)
