Electronics Forum: amps (Page 5046 of 7930)

Rad 5 performance: bent lead

Electronics Forum | Tue Jul 09 14:02:01 EDT 2019 | daniel_marquette

Unfortunately, I don't get the Jig but the component is always the same LED. I measured a sample of those and they are consistent from the tape and after the leads being cut. About 1-2% of the component from the tape are already bent so I'm still foc

Conformal Coating High Power Electronics PCBs

Electronics Forum | Wed Jul 03 09:43:47 EDT 2019 | SMTA-Pat

Hello All, Just wondering if some viewers on the forum have experience with conformal coating of PCBs for high power electronics. High power in this case meaning up to 800v. Any comments with regards differences seen from standard 12/24v electronic

PCB Inspection Templates

Electronics Forum | Wed Jul 03 13:14:01 EDT 2019 | markhoch

Hey Process Peeps, I'm looking for a supplier of PCB Inspection templates for use at Wave Solder Inspection to verify placement and polarity of specific component locations. (This would be a template that the inspector would overlay over the PCB dur

What is the best soldering gun?

Electronics Forum | Fri Aug 02 07:19:02 EDT 2019 | jchris

The response from SolderingPRO is quite amusing, considering he's the OWNER of Promation, distributor of Quick soldering irons in the US. By the way, Quick is a cheap, Chinese knockoff brand that has virtually no support in other countries other than

What is the best soldering gun?

Electronics Forum | Fri Aug 23 03:13:30 EDT 2019 | winslow_p

Hi! What is the best soldering gun? I would recommend the Weller 9400PKS 120V. I think it is the best. I have been using it for more than a year and I was satisfied. If in doubt, check out the best Soldering Guns review at https://solderingironguide.

Changing a DEK 265 Horizon to right to left

Electronics Forum | Sun Jul 14 16:46:38 EDT 2019 | rob1

I'm working on A DEK 265 Horizon and I need to convert it to right to left. I have changed the conveyor direction in software, however, the board stop position appears to be from 0 to 255 and I need it stop on the left hand side of the centre referen

Changing a DEK 265 Horizon to right to left

Electronics Forum | Mon Jul 15 09:03:44 EDT 2019 | dekhead

It uses the same BS position regardless of feed direction. In right feed, it passes Board under the camera and when (board @ stop) sensor detects board has passed, drops the BS and reverses conveyor direction. There is "Right Feed Delay" parameter to

Changing a DEK 265 Horizon to right to left

Electronics Forum | Tue Jul 16 16:15:14 EDT 2019 | dekhead

If a few extra seconds of cycle time won't hurt you, recommend putting at max (3.0 sec) it will cycle all the way over to the Board @ Left sensor before extending BS and reversing. Otherwise play with the timing and requirement may vary from product

which solder paste?

Electronics Forum | Tue Jul 16 11:12:18 EDT 2019 | jamesbowers

Time to get more solder paste and have no clearer ideas on the matter than last time. Going through the smaller jars on Digikey these two stand out (as I think they did last time!): One's Water Soluble (that's the one I got last time) and the other

MYDATA MY15E:F-MOT-MSETDYN conveyor transport/1250: amplifier DC-link too high

Electronics Forum | Wed Jul 17 02:31:30 EDT 2019 | mk15

I am looking for some help for where to look to fix this MY15E problem.After hardware initiation appear F-MOT-MSETDYN conveyor transport/1250: amplifier DC-link too high.Any suggestions? Thanks


amps searches for Companies, Equipment, Machines, Suppliers & Information

Electronics Equipment Consignment

High Precision Fluid Dispensers
2024 Eptac IPC Certification Training Schedule

High Throughput Reflow Oven
2024 Eptac IPC Certification Training Schedule

World's Best Reflow Oven Customizable for Unique Applications
Hot selling SMT spare parts and professional SMT machine solutions

500+ original new CF081CR CN081CR FEEDER in stock