Electronics Forum: amps (Page 5281 of 7929)

Support Fixtures or Systems

Electronics Forum | Mon Jul 30 10:44:37 EDT 2001 | hinerman

A few of the more common defects If bridging or insuffienct deposits occur on the printer, one of the first things to check is the tooling. Misplaced hard tooling pins or poorly designed fixtures have a nasty habit of breaking components on side

What is the std Resistivity for DI water at Aqueous

Electronics Forum | Tue Jul 31 13:55:27 EDT 2001 | mparker

Maintain DI water to 18 Meg Ohms resistivity. You can go down as low as 2 Meg ohms, in a pinch, but I would caution on what type of board you are running if trying to clean on 2 Meg ohm. Anything that is running an RF or high frequency circuit could

What is the std Resistivity for DI water at Aqueous

Electronics Forum | Tue Jul 31 20:05:11 EDT 2001 | davef

There is no the industry standard specification for resisitivity monitoring at aqueous cleaning. Beyond those posted here earlier by Mikie, guidelines can be found in the fine SMTnet Archives, for instance: (http://www.smtnet.com/Forums/Index.cfm?CF

ERSA scope?

Electronics Forum | Wed Aug 22 21:11:38 EDT 2001 | ksfacinelli

We have utilized the ERSA Scope for over one year. Our experience is that it is an excellent product in evaluation of problematic assemblies. It takes a little bit of time getting dialed in on the equipment but once you have it mastered it can see

Unsoldered Component

Electronics Forum | Tue Jul 31 18:49:20 EDT 2001 | arsmoriendi

i have a problem with some units that had one capacitor only soldered in one side, the geometry of the capacitor is 0805, our product during his life suffer a lot of stress (due temperature or vibration), some of those units are already with the cost

Unsoldered Component

Electronics Forum | Tue Jul 31 20:12:01 EDT 2001 | davef

If you've told your experts in Germany and US as little as you've told us, I'm not surprised they don't know dip. Sorry, I just snapped there for a moment. That wasn't politic, was it? Yes, it is possible that the other solder connection on this c

Multitroniks, Quad System and Tyco Info

Electronics Forum | Tue Jul 31 22:42:41 EDT 2001 | chip

In the past I have spoken to Multitronics sales reps and looked into the product line. I saw their equipment more suited for a smaller "mom and pop" type shop, I work for a mid size contract house and it wouldn't have come close to meeting my needs.

Multitroniks, Quad System and Tyco Info

Electronics Forum | Mon Aug 06 15:54:06 EDT 2001 | Fox

I think that anyone who has any questions about Tyco Electronics' offerings as far as equipment should check out their new web site: automation.tycoelectronics.com One other note about the references to Dynapert equipment and their link to Multitron

FV 7100 micro/mini coil inductors

Electronics Forum | Wed Aug 01 02:17:00 EDT 2001 | djarvis

Anyone placing micro,mini,midi spring inductors (as can be seen on http://www.coilcraft.com) with an FV7100? I can get the little suckers to "test" all day long, but soon as I go into production mode the vision system rejects around 20%. I've tried c

Thermally Conductive Epoxy

Electronics Forum | Wed Aug 01 11:11:38 EDT 2001 | JohnW

hi Folk's, Ok so I'm looking for some thoughts on Conductive Epoxy's. I'm trying to replace a material that i can place between a QFP and the PCB to transfer heat from the component to the PCB. The material has to be able to be injected thro' a hole


amps searches for Companies, Equipment, Machines, Suppliers & Information