Electronics Forum | Fri Aug 25 11:29:09 EDT 2006 | mika
Thanks all for Your input. The thing is that we want to avoid to go in to the pattern program and change the height in the middle of running a board. For ex. We start a product, feeders are loaded in advance in the feeder preparation area, operator
Electronics Forum | Wed Aug 23 08:08:25 EDT 2006 | aj
There are a few variables that you have to consider : 1. Hours available on Wave Machine ( are other products going thru the same wave) 2. What beat rate are the boards being supplied from previous station?i.e. do you envisage the waveto be a bottl
Electronics Forum | Thu Aug 24 12:53:56 EDT 2006 | russ
yes, it could have been from all 3 locations. without any detail whatsoever about your process or anythign it is impossible to help!! please check your incoming material prior to processing please check your reflow profile to ensure that max temp
Electronics Forum | Thu Aug 31 19:40:22 EDT 2006 | cardinal
A couple things on the Grid-Lok system. They now offer a top-side edge clamping system. The edge clamping system works very well for warped, twisted boards etc.. Using this system in the auto mode also allows the pins to contour to the geography of
Electronics Forum | Thu Sep 07 09:04:24 EDT 2006 | Doug Eidle
Hi, First off, I am the Pre Owned Equip. Business Mgr. for Speedline Technologies. We have a factory Renewed (our enhanced refurbishment process) available. You can contact your local Speedline MPM Rep for price and information. If board warp is
Electronics Forum | Thu Sep 14 06:45:11 EDT 2006 | Rob
Hi Mika, We had roughly the same set up - AP27 -CP6x2, GSMx2, VIP98 & we ran the thin boards with durastone routed pallets. If you route out a 0.4mm pocket on the pallet and either use kapton tape/high temp masking tape/ or 3M spraymount to hold
Electronics Forum | Thu Sep 14 05:11:29 EDT 2006 | ?
All, We are a contract manuf. for electronics. Since changeover to RoHS we still have customers due to one thing or the other telling us to run Non-RoHS. They are not exempt. What do we do ? do we tell them that we are not running their boards and
Electronics Forum | Fri Sep 15 16:30:13 EDT 2006 | russ
yes there is Caveman, (well maybe depending on your circumstances) you need to purchase a manual printer and print the connector then flip and print the other side. (you need a manual printer so you can print after the parts have nbeen reflowed, we
Electronics Forum | Tue Sep 26 00:42:36 EDT 2006 | fctassembly
Hello Brad, I think Greg is a mind reader!! Thanks for the opportunity to give an update to the forum on SN100CL Lead Free HASL. Conversions to SN100CL HASL is occuring at a rapid pace worldwide. As of July 2006, there were over 250 HASL machines ru
Electronics Forum | Tue Sep 26 10:22:51 EDT 2006 | SWAG
Histogram: Place standard tooling block in centernest. Jog camera over block. Jog z-axis to soft limit. Place a white card under camera. User mode to test. Turn board lamp on. From test menu, select histogram. With board lamp on and white under camer
SCANSMT is local stocking dealer who major in SAMSUNG,PANASONIC,YAMAHA,JUKI,FUJI mounter and MIRTEC,KOHYOUNG,PARMI,PEMTRON,CYBEROPTICS AOI&SPI,MPM,SJ,ESE Printers.HELLER,TSM Reflows are always have invertonries.welcome to visit us
Training Provider / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Floor 1,D Building,B area,Dongsheng Techwin Park,Bao'an District
Shenzhen, 30 China
Phone: 008618566662725