Electronics Forum | Mon Jul 08 17:07:15 EDT 2013 | wsdauchy
We have 2 CS9100 Schleuniger wire cut/strip machines. They do not have the DISPLAY/PC switch on the back of the CPU card. THe two machines come up PC mode. Any one know of a jumper setting on the CPU board that will allow the machnies to run in DI
Electronics Forum | Wed Jul 17 09:40:33 EDT 2013 | proceng1
I have a CM project that is a single sided pcb (not plated thru holes) and I have 3 axial resistors that the Customer wants placed on the "solder side" of the board. I cannot find an IPC-A-610 reference to putting parts on the wrong side of a single
Electronics Forum | Thu Aug 01 21:34:42 EDT 2013 | deanm
Techspray has a broad line of peelable solder masks. We use the Wondermask P for masking conformal coating as well. Call the company or rep to determine which product is best for you. I am not affiliated with Techspray in any way. If you get tired o
Electronics Forum | Wed Aug 07 10:40:19 EDT 2013 | simplycomplex85
They're hand placed and hand trimmed so they may be straight, may not be. And the solder (I think because its lead free) is a dull grey color to there is no reflection from any of it. The solder, lead, and board all show as a dark grey color under re
Electronics Forum | Thu Aug 08 13:11:00 EDT 2013 | shawnvike
I have a new product to build and it uses a SMD EMI board shield. I have never done this before. There are multiple components under the shield, do I place the components and then the shield and then reflow? Or do I have to reflow the components, ref
Electronics Forum | Tue Aug 13 10:22:13 EDT 2013 | mccabekev
We are seeing this the full length of the oven. We run a lot of double sided boards, so we cannot run them on the wire mesh. I checked inside the oven to ensure there was no build up of dropped parts that could block it. The temperature difference
Electronics Forum | Thu Sep 05 22:36:38 EDT 2013 | davef
Yes, providing your: * Inbound material does not compromise your process. * Soldering processes apply the proper amount of flux and activate it properly * Material handling does not contaminate your boards Recognize that the IPC requirements of less
Electronics Forum | Fri Sep 06 03:06:18 EDT 2013 | 5pcb
We are a complex pcb supplier in China. We are good at making prototypes and multilayer (8-20)layers PCB. If you think your boards are difficult enough, you can contact me. Let's talk details. sales2@dmele.com Name:Lily Tel:0086-0755-23006293.
Electronics Forum | Tue Sep 10 10:38:12 EDT 2013 | rway
Most of the PTH components are manually inserted. Some are auto-placed by our UIC machine. The parts are preped before install, so there is no need to trim the leads afterwards. The boards go through wave solder. The UIC machine has a clincher on
Electronics Forum | Wed Sep 25 13:39:11 EDT 2013 | bobpan
I have rarely seen a bad SRX controller card but it sounds like you may have a faulty card. Since i know you have 2 machines...i would swap them....make sure you take a picture of it or write down where all the cables plug in. The SRX board is locate
SCANSMT is local stocking dealer who major in SAMSUNG,PANASONIC,YAMAHA,JUKI,FUJI mounter and MIRTEC,KOHYOUNG,PARMI,PEMTRON,CYBEROPTICS AOI&SPI,MPM,SJ,ESE Printers.HELLER,TSM Reflows are always have invertonries.welcome to visit us
Training Provider / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Floor 1,D Building,B area,Dongsheng Techwin Park,Bao'an District
Shenzhen, 30 China
Phone: 008618566662725