Electronics Forum: cfm (Page 4991 of 7929)

Siemens HS180 Vision System placing compinents with PCB

Electronics Forum | Tue Jan 16 12:14:35 EST 2018 | emeto

There is no reason why you can't see these leads clear. Isn't there any way you can play with the lighting? I used to have Siemens machines and I want to say that it was possible. Go on the machine, start editing this shape code and find where you ca

Siemens HS180 Vision System placing compinents with PCB

Electronics Forum | Wed Jan 17 07:08:50 EST 2018 | emeto

Yeah, your machines are probably even older generation. I can tell you that what you can see is always more clear than what the machine can see(worked with 10 brands and probably 30 models). If you don't have good lighting and camera, some parts jus

Looking For Platform Set-up Validation (PSV) for UPS (OS/2) Software

Electronics Forum | Tue Jan 16 15:13:51 EST 2018 | ilavu

Hello All, I am in need for "Platform Set-up Validation" (PSV) for my Universal GSM2 with UPS version 4.5. My installation disk for PSV is bad and can not reinstall after hard drive crash.My machine is not register with Universal because some serial

Electrical Test problem

Electronics Forum | Wed Jan 17 12:10:47 EST 2018 | guilherme_castro

I have the follwing problem in our proccess we have to many problem with via hole and trought plated holes like voids air bubbles . During the eletricial test process our machine is not detecting this problems , the voids and air bubbles How

Juki gang picking same part number

Electronics Forum | Wed Jan 31 02:21:05 EST 2018 | robl

Hi Sr.Tech, We did before we posted, and they said no. We can get a round it, but it's a right pain, so I was wondering how anyone else forced it. I'm guessing with over 3000 views no one else does. Thanks, Rob.

Juki gang picking same part number

Electronics Forum | Fri Mar 23 04:57:26 EDT 2018 | rob

Hi Vojtěch, Thanks for taking the time to respond, I appreciate it. Yes we have the same options, but if you want to pick from the alternative feeders at the same time you have to use different part numbers. If you want to pick from alternatives w

Juki gang picking same part number

Electronics Forum | Fri Mar 23 08:42:18 EDT 2018 | georgetruitt

Rob, Can you add a suffix at the end of the part#, part#-1, part#-2, part#-3 (or use the feeder location part#slot123) and so on? Create those part# in the library. The machine will treat them as unique part#’s. You might be limited to a certain #

Intermittent vacuum on Hydra pipe

Electronics Forum | Fri Jan 19 08:10:03 EST 2018 | emeto

It should be one of these latches that got stuck in position. I had a similar problem(my200 machine) the other way around - my stays closed so I don't get any vacuum. The problem is that the whole block of latches should be replaced(on a my200 machin

I'm in the market for a HIGH end BGA rework machine, any recommendations?

Electronics Forum | Tue Jan 23 08:26:32 EST 2018 | rcooley4

I'm in the market for a HIGH end BGA rework machine, any recommendations? My budget some place between 30K to 100K, obviously the lower the better but I don't want to compromise quality of capability. Preferably I would like a machine that is capab

Has anyone heard of a no clean paste that can be cleaned in straight DI water ?

Electronics Forum | Fri Jan 26 12:57:34 EST 2018 | aqueous

Sorry to disappoint. No-Clean fluxes are resin-based. They are not soluble in water. Water soluble fluxes are by nature Organic Acid and are soluble in water AND must be cleaned within a short period after reflow as they remain conductive and corrosi


cfm searches for Companies, Equipment, Machines, Suppliers & Information