Electronics Forum: cord (Page 1 of 3)

CAD Export issue: S.O.S

Electronics Forum | Wed Jun 08 01:45:53 EDT 2011 | aoiguy

Update: I was able to import the csv pick & place data that was given, issue is that the data fails to over write the insert cords that have already been given with the cad data. Can not load the csv data without the first (cad) file loaded, so there

ESD....Limiting Resistor

Electronics Forum | Wed Jul 08 13:31:35 EDT 2009 | rway

Stephen, This link was also in my earlier post. "The wrist strap cord has a current-limiting resistor for personnel safety." http://www.intel.com/Assets/PDF/pkginfo/Ch_06.pdf

change from reflow to glue

Electronics Forum | Tue Jul 10 10:47:12 EDT 2012 | jorge_quijano

We do the same when it happens, we only warn the people arround to stay away while the oven is open, or delimitate the oven with a caution cord.

Panasonic NPM feeder cart

Electronics Forum | Mon Nov 25 20:52:47 EST 2019 | cbeneat

Are the arms pulling the cart all the way in? Possible part blocking the limit switch. does the cord have power? If I remember correctly, we once had to adjust the mechanical stops on one of ours so it would make the switch.

VME 162PA242 CARD ON CP40CV PROBLEM

Electronics Forum | Tue Oct 17 23:07:15 EDT 2023 | unsung

Also check the ribbon cord connecting to the motherboard it's a PCI board.

CAD Export issue: S.O.S

Electronics Forum | Tue Jun 07 20:56:47 EDT 2011 | aoiguy

Any and all input will be greatly appreciated. So here it goes. I'm having an issue where the cad I'm getting from customers is referencing pin 1 as the parts placement. This isn't an issue for surface mount, however the aoi machine that we have in

What is the best Low Volume Reflow System

Electronics Forum | Thu Feb 07 16:37:02 EST 2013 | jasowiii

This is good information but I had hoped to get specific manufacture and/or model infomation on equipment that someone has experience with. For instance I bought a Husqvarna model 455 (rancher) chain saw last year. I cut through 3 cords of fire wood

best way to get power to PCB

Electronics Forum | Fri Oct 31 09:14:25 EDT 2014 | gregp

OK...here is an example of something very cost effective and a very reliable... http://zierick.com/pages/sm_ipct.php The wire gets crimped in after reflow which is currently not automated. (WaveMasterLarry...this is the other end of the cord where i

Non-Waveable SMT Caps

Electronics Forum | Mon Jun 25 20:58:07 EDT 2001 | davef

Wolfgang: Is your company going-out of business? What "future is canceled"? What lights are being turned-out and doors being locked? Is there a fat lady tuning-up her vocal cords, too? [If so, sympathy.] Another "Dave F", now that�s something t

ESD considerations during Conformal Coating?

Electronics Forum | Mon Jun 01 11:38:28 EDT 2009 | operator

So would the proper technique be as follows: 1. Grounded operator picks up PCB from ESD rack and attaches a 1meg(wrist strap cord)shunt to ground to a grounding surface on the pcb. 2. operator sprays conformal coating onto pcb using a spr

  1 2 3 Next

cord searches for Companies, Equipment, Machines, Suppliers & Information

Selective soldering solutions with Jade soldering machine

High Throughput Reflow Oven
2024 Eptac IPC Certification Training Schedule

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.
2024 Eptac IPC Certification Training Schedule

Benchtop Fluid Dispenser
PCB Handling Machine with CE

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
PCB Depanelizers

Find a wide selection of nozzles, solder materials, storage solutions and more at SALESCON