Electronics Forum: electronic (Page 3956 of 7929)

Re: Fuji Ip2 macro BGA Placment

Electronics Forum | Sat Jan 29 00:30:09 EST 2000 | Micah Newcomb

Mike, I found the easiest way around your issue is to get your parts in T&R rather then trying to modify your machine. Some part manufacturers may be unwilling to T&R your part but there is always a ready and willing company whom would be happy to d

Re: Fuji Ip2 macro BGA Placment

Electronics Forum | Sat Jan 29 02:30:14 EST 2000 | Dean

5K$. Of course I remind myself that when these machines were designed BGA's didn't exist. I had no choice but to purchase this option as a new machine was out of the question and I place around 15,000 BGA's per month on this line. So the ROI was v

Solder balls after wave soldering

Electronics Forum | Fri Jan 28 05:06:01 EST 2000 | Istv�n Dominik

Hi! I have problems with the SMD boards during wave soldering. Mainly between the pins of the SOICs there are small solder balls. Maybe somebody had the same problem and could solve it. Please give me some ideas what causes this problem and how it

Re: Solder balls after wave soldering

Electronics Forum | Fri Jan 28 10:09:50 EST 2000 | mike d

Istvan, One possible reason for this is that you are using a water soluble flux in your wave solder machine. If you are and the boards are not pre heated long enough, the water in the flux does not evaporate before hitting the wave. When the water

Re: Solder balls after wave soldering

Electronics Forum | Sun Jan 30 03:06:50 EST 2000 | Roni H.

Hi, The major reason is that the flux is still "wet", you should fix the temp. profile (specialy preheat zone) so the evaporation of flux carriers will be better (anyway not to much !). Recommended: 1st preheat zone heating to ~70C , 2nd&3rd prehea

Re: NO CLEAN FLUX RESIDUE

Electronics Forum | Wed Jan 26 17:02:22 EST 2000 | Morris

One thing I've found that will create that white residue is when moisture comes in contact with that flux. 1. Verify that you are not introducing any moisture with the compressed air supply at the foam fluxer. 2. Replace the flux and clean the flu

Re: NO CLEAN FLUX RESIDUE

Electronics Forum | Thu Feb 10 13:06:05 EST 2000 | Chris McDonald

Instead of spending 15k on a spray fluxer spend a little bit on your foam tower. The narrower the foam head the less flux being applied. You might have to modify the foam tower but if works. I would switch fluxes though there are others out there tha

Re: High temperature solder paste for gold plated MCMs

Electronics Forum | Wed Jan 26 14:33:47 EST 2000 | Glenn Robertson

Tuan - How about Sn/0.7Cu? It's M.P. is 227 and it's readily available. If the leads are Gold plated you might consider pre-tinning them. If you need a higher temp alloy any of the major solder companies can help - I suggets you start with Ind

Re: High temperature solder paste for gold plated MCMs

Electronics Forum | Wed Jan 26 21:30:06 EST 2000 | Dave F

Tuan: Consider Sn 96.5/Ag 3.5 or Sn10/PB88/Ag02 also. As Glenn says, you had better get rid of that gold or you will never have a shiney connection. Not that a shiney connection means anything about the quality or reliability of your soldering. M

Re: High temperature solder paste for gold plated MCMs

Electronics Forum | Thu Jan 27 14:16:14 EST 2000 | Tuan Bui

I've tried Indium NC-SMQ92(96.5Sn 3.5Ag) on these MCMs and achieved only marginal wetting on pads and parts. The good wetting is what I try to achieve, shiny is what my engineers want (Prototype environment). Does pre-cleaning the PWBs in ultrasonic


electronic searches for Companies, Equipment, Machines, Suppliers & Information

Winsmart Electronic Co.,Ltd
Winsmart Electronic Co.,Ltd

Manufacturer of PCB depaneling and PCB soldering machines since 2005, products include CE approval V-groove PCB depanelizer, PCB router, PCB punching machine, laser depaneling, hot bar soldering machines and soldering robots.

Manufacturer

Liwu Industrial Park, Yuanzhou Town, Boluo
Huizhou, 30 China

Phone: +86-138-29839112