Electronics Forum | Thu Feb 14 10:23:32 EST 2013 | vincent_qms
Hello, we have a DEK 248 just acted up with the squeegee orror. unit powered up initiated and when throght setup a job fine but when we started printing, the back squeegee came down, touched the stencil, stay for about 5 second then came back up with
Electronics Forum | Thu Feb 14 13:10:58 EST 2013 | markhoch
I had this problem once a loooooooong time ago with a 248 that was at my previous place of employment. If I remember correctly, my issue was caused by a set screw on the drive gear that had worked itself loose. My issue was stright forward and quickl
Electronics Forum | Fri Feb 15 21:52:06 EST 2013 | nikyta
Most likely it is a faulty cable in the e-chain . You can test it in diagnostic: lower the back squeege and manually move back and forth for its entire travel the print carriage while monitoring the sensor output of the squeege. You will see at some
Electronics Forum | Thu Feb 14 17:00:42 EST 2013 | richardc
I am trying to use Mydata TM8C feeders that work fine on a TP93 running 1.6.18 TPsys but are not recognized by a TP94 machine running 1.4.7 TPsys. I get a green flashing light instead of a solid green. I can initialize the hardware but can not proc
Electronics Forum | Mon Apr 01 20:40:49 EDT 2013 | aemery
Quite sure it is one of the follow things. Squeegees are not tall enough (using after market blades); Are you using a stencil adapter? bottom surface of the stencil must be even with the top of the stencil shelves; printhead assy. is modified, faile
Electronics Forum | Fri Feb 15 11:18:08 EST 2013 | richardc
Does anyone know the mechanical differences between a TPsys 1.6 version feeder and a 1.4. I only need to have one feeder for the 1.4 machine and would modify a 1.6 feeder if that is an option. Otherwise, does antone have a 1.4 version feeder they w
Electronics Forum | Fri Feb 15 13:45:18 EST 2013 | cowens
We have a MPM UP2000. We are getting a hardware limit error when we turn the machine on and try to reset. The F14 fuse blows every time we replace it. The downstop is the first axis that it tries to go through but we get this error. Any help would be
Electronics Forum | Tue Feb 26 07:46:04 EST 2013 | stephendo
If anyone still disagrees with you point, out that the "of each" refers to individual pads. If the 95% refered to 95% of the pads it would not have said "of each". Also someone correct me if I'm wrong but isn't this standard to do with solderabilit
Electronics Forum | Tue Feb 19 18:51:45 EST 2013 | tombstonesmt
We've had great success with acrylic based cut with xylene. Very accurate with little to no masking necessary for keepout areas, very rarely have to make adjustments on our Asymtek. On the other hand we have an Asymtek dedicated for silicone coatin
Electronics Forum | Sat Feb 23 14:49:11 EST 2013 | duso02
Too bad you couldn't make it to the APEX show. Lots of equipment, and coating experts on hand. To answer your questions: 1. Yes, multiple brands, as well as non-UV cure. 2. Yes, there are. What you choose really depends on a lot of other info. 3. Ye
Manufacturer of PCB depaneling and PCB soldering machines since 2005, products include CE approval V-groove PCB depanelizer, PCB router, PCB punching machine, laser depaneling, hot bar soldering machines and soldering robots.
Liwu Industrial Park, Yuanzhou Town, Boluo
Huizhou, 30 China
Phone: +86-138-29839112
