Electronics Forum | Fri Jul 19 16:27:38 EDT 2013 | microaide
I think I have the vision problems figured out. There were two problems. 1) The Alignment type was set to "Small" for my TQFP48 part. It should have been set to "Complete". This is a clear case of poor documentation. The AutoProgram manual lists the
Electronics Forum | Fri Jul 19 10:19:01 EDT 2013 | rway
We have inline reworkers, so this time has been factored in. We currently use Siemens S25/20 machines with M1 systems. The placement machines run a little slower than the AOI at times so there is time to perform review, most of the time. It's not
Electronics Forum | Fri Jul 19 18:21:17 EDT 2013 | microaide
We recently purchased some used Quad 4C machines. One of them does not seem to keep a stable origin reference point. I teach the nozzle and component pickup coordinates, then suddenly everything seems to be off by .030 to .040 inches in the X axis. I
Electronics Forum | Mon Jul 22 14:01:31 EDT 2013 | jax
HMP can mean a lot of things, although it is normally used as the generic name for one of the following alloys: Pb93.5 Ag1.5 Sn5 (296°C-301°C) Pb95 Sn5 (308°C-312°C) Pb97.5 Ag1.5 Sn1 (309°C) If you are talking abou
Electronics Forum | Tue Jul 23 13:36:52 EDT 2013 | jsmorse
Does anyone have info on the "Cycle Steel" function on the Fuji XP141 machines. I am new to the industry and have not had any luck finding information on it. I talked to Fuji and they just tell me to leave it on, it will help with placement. We hav
Electronics Forum | Wed Jul 24 22:24:07 EDT 2013 | mac5
When we first got our XP1’s the cycle steal was on a schedule. We would have boards running good and then start placing off in the middle of a run. We finally noticed that the cycle steal had run just prior to the parts being misplaced. We have turne
Electronics Forum | Thu Aug 01 16:28:17 EDT 2013 | jimmyboz
Does anyone have info on the "Cycle Steel" > function on the Fuji XP141 machines. I am new to > the industry and have not had any luck finding > information on it. I talked to Fuji and they > just tell me to leave it on, it will help with > pl
Electronics Forum | Mon Jul 29 11:20:10 EDT 2013 | rgduval
Is there any particular reason you're looking at getting a dedicated machine?! The first question that pops to mind is...are you having so many mis-prints that you need dedicated equipment at the site to mitigate the issue? If so, I know you've bee
Electronics Forum | Sat Jul 27 17:21:19 EDT 2013 | ericrr
A mistake happened at our company before I got there where a wrong value was used, so now we have to check it with someone else to make sure the old empty reel is the same value as the new full reel. Some months after I started, I decided to check t
Electronics Forum | Wed Aug 14 13:24:18 EDT 2013 | eadthem
We just designate shelves with signs, PULL HERE, Move UP NEXT, MOVE UP 2nd, MOVE UP 3rd, We also keep paste in the incoming case, if it has one until its time to open it. Our operators are the ones who stock it and as long as they know they own
Manufacturer of PCB depaneling and PCB soldering machines since 2005, products include CE approval V-groove PCB depanelizer, PCB router, PCB punching machine, laser depaneling, hot bar soldering machines and soldering robots.
Liwu Industrial Park, Yuanzhou Town, Boluo
Huizhou, 30 China
Phone: +86-138-29839112