Electronics Forum | Sat Sep 27 17:58:12 EDT 2014 | isd_jwendell
What?? You haven't unpacked it yet? I unpacked mine (CSM7100V) the day it arrived. You need to make sure that all the parts are there and undamaged. Training has value. It is hard to justify that much money to get one of the Essemtec techs on-site.
Electronics Forum | Tue Sep 30 13:41:51 EDT 2014 | cyber_wolf
In 25 years of profiling, I have never seen a reflow profile make TOMBSTONES better. I have had "experts" come in an adjust our ovens to the "magic profile." The AOI data has never shown improvement from profile changes. EVER...EVER. As long as you
Electronics Forum | Mon Sep 29 15:28:29 EDT 2014 | dustin
After getting the last issue I had fixed through here. I thought I would try to see if there is a solution for another issue. I have and ekra e5 screen printer and it has a problem with the blades not dropping when they should. If I set up single dir
Electronics Forum | Wed Oct 08 11:16:12 EDT 2014 | cbeneat
We are having an intermittent issue with a certain board on our wave solder line, machine is a Vitronics 6922 Delta Wave, leaded process. There are 2 fuse holders on one edge of the board that are not getting solder all the way thru the barrel every
Electronics Forum | Mon Oct 13 08:43:56 EDT 2014 | rob
Hi Larry, Picture a old lady with a set of knitting needles with leads attached to them, pressing the needles into different points of the PCB (pads, test points or component leads) and measuring resistance, inductance, waveforms etc between these p
Electronics Forum | Mon Oct 13 15:33:36 EDT 2014 | rgduval
So...today, we were able to get rid of the z axis not mounted error. It looks like we did so by modifying the settings in axes location (matched them to the beam 1 settings). Now, when we try to lower the nozzles, we can hear a relay or switch clic
Electronics Forum | Mon Oct 13 16:32:55 EDT 2014 | tombstonesmt
Designator>Part Number>Alternate. 2D labels are placed on all slots of the machine, operator scans slot, scans reel with unique material ID. Green light if it's good, red light if it's bad. Our software cannot lock out a machine if there is an incorr
Electronics Forum | Wed Feb 18 13:32:58 EST 2015 | stevea
Hi Rob, Not sure if you made any decision on your SPI requirements. The recently established VisionMaster (Long history of previously shuttered business names) company sells products similar too, but not the same as the past "VisionMaster branded" p
Electronics Forum | Sun Oct 19 06:42:01 EDT 2014 | timbo292832
im designing a circuit that will require the use of a edge connector so it can connect to another circuit. i need to do this so i can get both micro controllers communicating i have done a bit of research and am thinking about using a pcb manufact
Electronics Forum | Mon Oct 20 18:53:39 EDT 2014 | warwolf
pci express x1? https://www.google.co.nz/search?q=pci+express&client=firefox-a&hs=ZJi&rls=org.mozilla:en-GB:official&channel=sb&source=lnms&tbm=isch&sa=X&ei=DZJFVKvRDaXemAXaxoCgDA&ved=0CAgQ_AUoAQ&biw=1173&bih=849#rls=org.mozilla:en-GB:official&chann
Nordson Electronics Solutions makes reliable electronics an everyday reality. Our ASYMTEK, MARCH, and SELECT brands deliver precision fluid dispensing, conformal coating, plasma treatment and selective soldering equipment.
2747 Loker Ave West
Carlsbad, USA
Phone: 18002796835
