Electronics Forum: feel cp or cp642 (Page 1 of 2)

fuji CP642 or CP643

Electronics Forum | Tue Oct 02 03:35:05 EDT 2012 | benreben

Hi all, depending on your experience is there a difference between CP642 and CP643? what is the most stable machine service level? there know problem with these machines? Thanks Regards,

fuji CP642 or CP643

Electronics Forum | Tue Oct 02 10:26:17 EDT 2012 | jimmyboz

If I had a choice I would choose a CP642 90% of the time. The loading system on the 643 can load 2 PCBs at the same time but is complicated. If 2 seconds on PCB load time is critical on your production choose the 643, if not, choose the 642.

Recomendations? Fuji CP7 or Univ HSP4797?

Electronics Forum | Wed Jun 23 10:05:17 EDT 2004 | exmaintenanceleader

Hi Grant, I'm ex Fuji service engineer I install also at Sagem Czecz Republik (Kladnow near Prague) in 2000 they use at new lines MPM- 2XCP643E and 1xUniversal GSM (French owen (I do not remember the exacly tipe) at second hand line they use 2x and

Recomendations? Fuji CP7 or Univ HSP4797?

Electronics Forum | Wed Jun 23 10:26:53 EDT 2004 | exmaintenanceleader

Grant and all! CP-2 is the oldest fuji as I have been operated. CP-3 is built in 1989 as a new mc. Now 15 mc I now they runs in 3 shift widouth problems when they need countinous runing comes the problems. conroll card and relay contact problems at

Looking to Buy CP4-3 or CP6

Electronics Forum | Wed Dec 17 12:51:56 EST 1997 | Mike Cox

Anybody have one of these machines feel free to call or email me Mike Cox 1-208-887-1000 MCCOX94@AOL.COM Thanks for your help

Re: Looking to Buy CP4-3 or CP6

Electronics Forum | Wed Jan 28 15:42:26 EST 1998 | Anonyous

Anybody have one of these machines feel free to call or email me Mike Cox 1-208-887-1000 MCCOX94@AOL.COM Thanks for your help You should really consider buying a Siemens Siplace machine. They are much better and service/support is excellent

Fuji Pick and Place Machines

Electronics Forum | Wed May 19 16:57:08 EDT 2004 | ricardof

We have in our facilities in Mexico more than 150 FUJI machines (CPs, IPs, QPs, GPs), they're in fact Bombproof, but it is not amazing to do that with 1206, SOTs on SOPs, we just feel a kind of disappointed with that 10K hours service, that means yo

CP642 Ballscrew Replacement

Electronics Forum | Thu Jun 25 07:54:02 EDT 2009 | brucow

Hi and thank you for your replies, I feel a lot more confident about tackling the job with your instructions, many thanks. We haven't seen any accuracy issues, and the ballscrew has been making the same banging/knocking noise when changing direction

Re: 1005 using Fuji CP3 CP4-3

Electronics Forum | Thu Jul 29 01:57:49 EDT 1999 | KEVIN SIMPSON

Dear Forum Members, Is their anyone who is familar with 1005 placement using a Fuji CP3 and a CP4-3 to perform at CP642 spec's? I have heard of a number of companies doing this. Are there any tech sheets or other site's that may have this pr

CP642 Ballscrew Replacement

Electronics Forum | Wed Jun 24 08:19:59 EDT 2009 | fujiphil

Hi, Procedure how to replace the x-ballscrew of CP642. 1. Before you remove the x-motor, remember the pulse of x-axis motor just it turn ON the zero set sensor. Pulse usually at 1000pls. +/-50pls. 2. Turn Off the machine. 3. Compress the two ballsc

  1 2 Next

feel cp or cp642 searches for Companies, Equipment, Machines, Suppliers & Information

consignment program

Easily dispense fine pitch components with ±25µm positioning accuracy.


Inspection mirrors for electronic rework and repair.


Best Reflow Oven