Electronics Forum: hybrid profile bga (Page 1 of 88)

hybrid solder joints

Electronics Forum | Thu May 13 21:45:14 EDT 1999 | ardis

I am seeing reflow around my signal pins after being subjected to a profile of 204c for 1 minute and 225c for a min of 30 seconds. Signal pins are soldered into a copper plated alum. case with SB5 and then silver plated. The pins have a hot oil tin

Re: hybrid solder joints

Electronics Forum | Fri May 14 00:28:09 EDT 1999 | Mike D.

I am seeing reflow around my signal pins after being subjected to a profile of 204c for 1 minute and 225c for a min of 30 seconds. Signal pins are soldered into a copper plated alum. case with SB5 and then silver plated. The pins have a hot oil

bga warp

Electronics Forum | Wed Sep 11 16:57:04 EDT 2002 | bigwop

I've seen this problem caused by the cool down. > On a 7 zone oven I made a profile to peak at zone > 5 to give some semblance of control to the cool > down. The component can develope a big delta T, > because of the difference of materials Che

bga warp

Electronics Forum | Wed Sep 11 13:20:37 EDT 2002 | stepheno

I've seen this problem caused by the cool down. On a 7 zone oven I made a profile to peak at zone 5 to give some semblance of control to the cool down. The component can develope a big delta T, because of the difference of materials

bga warp

Electronics Forum | Wed Sep 11 23:20:44 EDT 2002 | scottefiske

Profiles are absolutely the first course of action to validate. A few additional questions would be: * Moisture can cause warping as well, verify the manufacturers recommended handling procedures were followed. * Where is the suspect BGA located

Hybrid reflow profile

Electronics Forum | Mon Oct 03 10:20:43 EDT 2005 | davef

Follow your component supplier recommendations. For instance: Xilinx says their lead-free alloy for their BGA spheres is SnAgCu, and liquidous is 217*C and they want you to peak at 230 - 235*C for good wetting according to their reflow guidelines.

mirco bga stencil opening

Electronics Forum | Thu Sep 12 09:15:29 EDT 2002 | mhoughton

I have printed and placed similar devices in high volume with exactly this spec for a couple of years with no problems, are you using laser cut stencils and what type of solder paste are you using? and what is the end use of the product as it may nee

mirco bga stencil opening

Electronics Forum | Thu Sep 12 10:45:29 EDT 2002 | pbarton

We have used a laser cut stencil 0.15mm (0.006") thick with 0.3mm (0.012") square apertures radiused in the corners 0.06mm (0.0025") to aid paste release. This approach with the (type 3) paste we use has proven successful on thousands of devices plac

oven profile

Electronics Forum | Fri Mar 28 22:01:00 EST 2003 | MA/NY DDave

Hi Yes I agree, yet this subject is about Tombstoning and oven profile or even oven working correctly across the entire product is a sub-set of how one gets those little chip babies to sit and stay where they belong. Flat and Heeling like their mast

Re: looking for bga rework station

Electronics Forum | Fri Apr 09 12:46:10 EDT 1999 | Bob Barr

I have been using an Air-Vac DRS-22 for almost two years with very good results. Once a profile is developed it is very repeatable. The DRS-22 is no longer available, however. It has been replaced by the DRS-24. Unfortunately, the DRS-24 has a lo

  1 2 3 4 5 6 7 8 9 10 Next

hybrid profile bga searches for Companies, Equipment, Machines, Suppliers & Information

Dispenser Pumps

Real Time Process Control BREAKTHROUGH for Dispensing Industry.
Benchtop Fluid Dispenser

Want to know where to find the best AOI system? - Read testimonials.


High Precision Fluid Dispensers
Non-heated dispensing system

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
SMT spare parts

MIRTEC - the Global Leader in PCB INSPECTION Technology.