Electronics Forum: immersion silver rework (Page 1 of 35)

PCB immersion silver discolouration

Electronics Forum | Tue Sep 23 10:06:29 EDT 2008 | Sean

Hello Vlad, Davef, Your valuable inputs are much appreciated. Many thanks, Sean.

PCB immersion silver discolouration

Electronics Forum | Sat Sep 20 07:11:28 EDT 2008 | Sean

Hello All, I used to hear that PCB with immersion silver finishing, its non component location pads, tend to be discolour (Yellowish) after went through heat cycle, such as reflow oven. However, if the component solderbility on the PCB is OK, can w

PCB immersion silver discolouration

Electronics Forum | Sun Sep 21 10:55:52 EDT 2008 | vladig

As long as the surface is solderable, you should be fine. Silver tarnish a well0-known thing. Make sure, though, there is no sulfur (S) "around". Regards, Vlad

PCB immersion silver discolouration

Electronics Forum | Mon Sep 22 15:32:20 EDT 2008 | davef

We see this fairly often. It doesn't affect solderability. Our analysis makes us think this coloration is copper. The reason copper appears on the surface may be that heat cycles increase the thinness and porosity of the immersion silver [IAg] coatin

Immersion silver life span

Electronics Forum | Wed Apr 20 08:06:21 EDT 2005 | davef

We'd reject the boards because: * Vacuum seal is punctured. * HIC is expired. One of the nice things about immersion coatings is that the fab can rework the coating. You cannot do that with other coatings. Finally, every HIC that we investigated c

imm. silver

Electronics Forum | Thu Aug 29 17:51:43 EDT 2002 | nifhail

I have seen several Imm Ag pad on the assembled board which have a copper colorleaching through the silver plating This happened on the pad which was not deposited with paste during the assembly process. Don't know if it is a problem, but we only h

imm. silver

Electronics Forum | Fri Aug 30 16:25:21 EDT 2002 | davef

Imm silver holds-up to multiple thermal cycles very well. The things, we guess, are happening to make imm silver tough to solder after heating and sitting are: * Oxidation of the silver. * Reduction of the co-deposited organic anti-tarnish [used in

Board with immersion Tin

Electronics Forum | Mon Nov 25 16:12:52 EST 2002 | russ

there is a good article by AIM solder regarding tin. In a nut shell, if you do not apply flux or heat to tin finish you will never degrade it! I agree with the others that you need to check the thickness of the pure tin layer. We have forbidden ti

Immersion silver life span

Electronics Forum | Wed Apr 13 05:48:52 EDT 2005 | charly

hi' i need advise on immersion silver PCb shelf life. 1) what is the shelf life for Immersion silver PCB? 2) iF PCB expire, can we bake the immersion PCB? what temp & duration? 3) How long can we keep the pCB again after rebaking? (with vacuum seal)

Re: White tin immersion finish

Electronics Forum | Wed Aug 05 07:46:46 EDT 1998 | Earl Moon

We have mixed to negative feelings about Omikron, but I beileve it is due to problems with the board fabricator rather than the process itself. When done properly, our Omikron boards have had very good solderability. However, we have had several

  1 2 3 4 5 6 7 8 9 10 Next

immersion silver rework searches for Companies, Equipment, Machines, Suppliers & Information

zestron pcb cleaning webinars

PCB Assembly Supplies - ONLINE STORE
XTECH AUCTIONS

MSD Dry Cabinets
Industry 4.0 Reflow Oven

Want to know where to find the best AOI system? - Read testimonials.
Your 2021 Eptac IPC Training Schedule

Private label coffee for your company - your logo & message on each bag!