Electronics Forum: mpm up2000 y snugger (Page 1 of 2)

Stencil Printer comparison

Electronics Forum | Wed Nov 20 16:27:15 EST 2002 | pjc

FYI: MPM does in fact offer alternate board support tooling than the vacuum box system. They have the X and Y snugger tooling, which clamps the board and uses magnetic support pins. If you are looking at a used UP2000, check to see what tooling it ha

MPM AP25/HiE, side snuggers

Electronics Forum | Tue Mar 06 08:33:40 EST 2007 | cardinal

You can get a topside edge-clamping system to fit your AP HI E printer from Gridlok. They make a universal tooling system and topside edgeclamping system for the AP series and UP 2000 series printers. The Y snugger tooling option when ordered with t

MPM UP2000

Electronics Forum | Wed Sep 30 05:10:28 EDT 2015 | aemery

SWAG does make a good point. The tool he is talking about is located on setup page 1 in the vision box and is labeled FP Mode (Fine Pitch) mode. BY default the setting is "0" this means that once the machine is put into auto mode the camera or visio

UP2000 with grid-lok question

Electronics Forum | Tue Jan 23 13:10:10 EST 2007 | jax

This is something a DFM should catch. Best Option: Add Break-Away rails to the board. Worst Option: Buy a true on-contact printer... (normally referred to as the Y-Snugger option)

AP 25Hie

Electronics Forum | Tue Jan 13 19:16:03 EST 2004 | pjc

Dedicated tooling uses what MPM calls an "H" tower. You mount the board support plate (dedicated tooling) on top of the H tower. If boards are only single-sided SMT, meaning only components on one side, the board support plate is flat with vacuum hol

Screen printing warped boards

Electronics Forum | Mon Apr 24 09:43:47 EDT 2006 | printerman

What you describe is the X snuggers fitted into the workholder which do need either a flat board or good vacuum to work. There are several solutions. One solution you can try yourself is to use Vacuum cups, ( bellows type) designed into the workholde

VY Software limit MPM UP2000

Electronics Forum | Thu Aug 06 11:41:10 EDT 2009 | swag

Is the aperture pattern on your stencil centered in the Y?

MPM UP2000

Electronics Forum | Wed Sep 30 06:22:23 EDT 2015 | mervin

MPMENG, Thank you so much for taking the time to help. The machine has Y snuggers and flippers. The Pcb is loading in the center all the time. The driver cards look fine there is no obvious faults on them or partially burned. The machine was not in

Screen printing warped boards

Electronics Forum | Mon Apr 24 13:23:37 EDT 2006 | pjc

Use the photo sensor to stop boards instead of the hard-stop. There is also an ultrasonic sensor upgrade. A little more robust than optical. Y Snugger Tooling upgrade is kind of pricey and they like to do that in the plant. But, I've known that upgr

MPM UP2000 HiE Z problem

Electronics Forum | Fri Aug 07 09:53:12 EDT 2009 | kpm135

The Z-axis Drive card on our MPM UP2000 HiE fried. We replaced it with a new card, setting all the jumpers to match the old card. After that we had to recalibrate the Z-axis and the snugger height but the problem is that the camera is now too close t

  1 2 Next

mpm up2000 y snugger searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling with CE

MSD Dry Cabinets
Potting and Encapsulation Dispensing

Outstanding liquid dispensing and UV curing, all within one platform, watch the video.
Non-heated dispensing system

High Throughput Reflow Oven